background image

 090418

228-1692 REV 8

13

KEPCO, INC. 



 131-38 SANFORD AVENUE 



  FLUSHING, NY. 11355 U.S.A.



  TEL (718) 461-7000



 FAX (718) 767-1102

http://www.kepcopower.com   



 email: hq@kepcopower.com

Active.

 Active mode (default setting) is necessary

for the power supply to function properly and safely
with inductive loads and constant-current-type active
electronic loads. Active mode can also be used with
resistive loads. Table 5 indicates how the power sup-
ply responds to a command to go from Output ON to
OFF. When the output is disabled, the unit is set to

voltage mode, voltage is set to zero and both current
protect and voltage limit are set to maximum. When
the unit is enabled, the pre-existing settings for volt-
age, current protect and voltage limit are restored.

FIGURE 6.  MAX/MIN SETTING MENU

WARNING

For both inductive loads and con-
stant-current-type active electronic
loads when the BOP output is set
to OFF, a path is provided for
absorbing either the energy accu-
mulated in the reactance of the load
during the ON state, or energy
delivered by an electronic load.
This prevents damage to the load
and power supply as well as pro-

viding safety for the user. However,
In addition to the built-in safety fea-
tures, constant-current-type active
electronic loads must be adjusted
to zero and the BOP front panel
LCD must read 0V, minimum cur-
rent, before handling the power
supply-to-load connections. 

Resistive. 

This mode, as the name suggests, is

useful for resistive loads. Table 5 indicates how the
power supply responds to a command to go from
Output ON to OFF.

TABLE 5.  POWER SUPPLY BEHAVIOR WHEN OUTPUT IS SET TO OFF

LOAD TYPE

SETTING

If unit was in Voltage Mode when output OFF 

command issued.

If unit was in Current Mode when output OFF 

command issued.

ACTIVE

• Unit remains in voltage mode.
• Voltage set to zero.
• Both ± Current Protect set to maximum.
• Both ± Voltage Limit remain at maximum.

• Unit set to voltage mode.
• Voltage set to zero.
• Both ± Current Protect remain at maximum.
• Both ± Voltage Limit set to maximum.

RESISTIVE

• Unit remains in voltage mode.
• Voltage set to zero.
• Both ± Current Protect set to minimum box values.
• Both ± Voltage Limit. remain at maximum.

• Unit remains in current mode.
• Current set to zero.
• Both ± Current Protect set to minimum box values.
• Both ± Voltage Limit set to maximum,

BATTERY

• Unit set to current mode.
• Current set to zero.
• Both ± Voltage Protect. remain at maximum.
• Both ± Current Limit set to maximum.

• Unit remains in current mode,
• Current set to zero.
• Both ± Voltage Protect set to maximum.
• Both ± Current Limit remain at maximum.

VOLTAGE

SOURCE

VOLTAGE

CURRENT

0.0000 0.0000

Summary of Contents for BOP 10-100MG/ME

















Reviews: