Superseded Products
The following superseded products may be powered from
the Advanced RPS. Again their usage is subject to the
total power limitation of 480 watts.
Superseded Products requiring a 60 watt
Power Module
LinkBuilder Hubs
3C215A
Hub 100 Management Unit
3C250-TX
FMS 100 TX
3C16665
FMS II Fiber (also with 3C16630A or
3C16632 Management Module and
3C1206X Transceiver Module fitted)
3C16670
FMS II 12-port TP (also with 3C16630A or
3C16632 Management Module and
3C1206X Transceiver Module fitted)
3C16671
FMS II 24-port TP (also with 3C16630A or
3C16632 Management Module and
3C1206X Transceiver Module fitted)
3C16672
FMS II Telco (also with 3C16630A or
3C16632 Management Module and
3C1206X Transceiver Module fitted)
3C510510B
FMS TR 12-port
3C510511B
FMS TR 24-port
NetBuilder Routers
3C8200C
NetBuilder Remote Office 200
3C8201C
NetBuilder Remote Office 201
3C8221C
NetBuilder Remote Office 221
3C8222C
NetBuilder Remote Office 222
3C8223C
NetBuilder Remote Office 223
3C8224C
NetBuilder Remote Office 224
3C8227C
NetBuilder Remote Office 227
3C8228C
NetBuilder Remote Office 228
3C8323C
NetBuilder Remote Office 323
3C8327C
NetBuilder Remote Office 327
3C8421C
NetBuilder Remote Office 421
3C8422C
NetBuilder Remote Office 422
3C8423C
NetBuilder Remote Office 423
3C8424C
NetBuilder Remote Office 424
3C8427C
NetBuilder Remote Office 427
3C8523C
NetBuilder Remote Office 523
3C8527C
NetBuilder Remote Office 527
LinkSwitch
3C16900
LinkSwitch 1000 24-port (also with
3C1206x or 3C16920/2 modules fitted)
3C16901
LinkSwitch 1000 12-port (also with
3C1206x or 3C16920/2 modules fitted)
3C16940
LinkSwitch 3000 (also with 3C1206x or
3C16920/2 modules fitted)
DISCLAIMER
Information in this document is subject to change without notice and
does not represent a commitment on the part of 3Com Ireland. 3Com
Ireland reserves the right to revise or change this document without
obligation of 3Com Ireland to notify any person of the revisions or
changes. Information contained in this document is believed to be
accurate at the time of publication but no liability whatsoever can be
accepted by 3Com Ireland arising out of any use of this information.
This document, or any part of it, must not be copied or reproduced on
any medium without the prior consent of 3Com Ireland.
In the unlikely event that this product is found to be damaged on
arrival, or fails to function once installed, you should contact your
distributor or reseller for advice.
ACKNOWLEDGEMENTS
3Com, AccessBuilder, NetBuilder, LinkSwitch and LinkBuilder are
registered trademarks of 3Com Corporation. Registered trademarks
are registered in the United States, and may or may not be registered
in other countries.
SuperStack is a trademark of 3Com Corporation.
Other brand and product names may be registered trademarks or
trademarks of their respective holders.
Part Number: DUA1607-2AAA02
Revision: 00
Issued:July 11th, 1997
© 1997 3Com Technologies
3C16941
LinkSwitch 3000 TP (also with 3C16920/2
modules fitted)
3C32700A
Switch 2700 OC-3 Multimode ATM
3C32710A
Switch 2700 DS-3 ATM
3C32711A
Switch 2700 OC-3 Singlemode ATM
AccessBuilder
3C7204
AccessBuilder 2204
3C7208
AccessBuilder 2208
LinkConverter
3C8252A
LinkConverter II 252
3C8254A
LinkConverter II 254
3C8352A
LinkConverter II 352
Superseded Product requiring a 100 watt
Power Module
3C16900
LinkSwitch 1000 24-port with 3C16930
module fitted
3C16901
LinkSwitch 1000 12-port with 3C16930
module fitted
3C16940
LinkSwitch 3000 with 3C16930 module
fitted
3C16941
LinkSwitch 3000 TP with 3C16930 module
fitted
3C32700A
Switch 2700 OC-3 Multimode ATM
3C32710A
Switch 2700 DS-3 ATM
3C32711A
Switch 2700 OC-3 Singlemode ATM
3C220000A
LinkSwitch 2200
A
D
V
A
N
C
E
D
RPS P
O
W
E
R
M
O
D
U
L
E
S
(3C16072 & 3C16073)
U
S
E
R
G
U
I
D
E
Introduction
The SuperStack™ II Advanced RPS Power Modules are
designed to provide redundant power supplies, from the
SuperStack II Advanced RPS chassis (3C16070/1), to the
products in 3Com’s SuperStack II range. There are two
modules; a 60 watt capacity unit (3C16072) to supply most
of the products and a 100 watt unit (3C16073) for those
products with a higher power requirement. To connect the
power module to the active units, use only the cables
supplied with this module or the special ‘Y’ cables available
from your supplier.
For more general information and warranty details
for these products, please refer to SuperStack II
Advanced RPS User Guide, part number
DUA1607-0AAA0X.
The optional SuperStack II Advanced RPS Management
Module provides management information to a Network
Manager. Details of the management functions are in the
Management Module user guide, part number
DUA1608-0AAA0X.
This guide is written for the installation engineer and the
network administrator who manages and maintains the
network.
Safety Information
L’Information de Sécurité
Sicherheitsinformationen
Please read the safety information in the Advanced
RPS Chassis User Guide before installing the module.
Veuillez lire les instructions de sécurité dans le
manual d’utilisation du chassis de l’Advanced RPS
avant d’installer le module.
Lesen sie vor der Installation des Modules die
Sicherheitsinformationen in der Advanced RPS
Gebrachsanweisung.
Power Supply And Fuses
All power is supplied and fused from the Advanced RPS
chassis. There are no user-replaceable fuses on the Power
Modules.
Installing The Module
Power Module Usage
■
You must not connect units with a total power require-
ment of more than 480 watts to any one chassis.
■
Single Power Modules must be considered as supplying
their rated power.
■
Each Power Module in the full redundancy configuration
may be considered as supplying half its rated power.
The SuperStack II Advanced RPS Power Modules may be
hot-inserted into the chassis.
It is important that the Power Modules are
cooled effectively. We strongly recommend
installing the Power Modules as evenly as
possible between the top and bottom slots.
■
Take off the blanking plate by removing the fixing screw.
Keep the blanking plate and screw in a safe place. You
will need it, if you remove a module, to close the chassis
to the ingress of dust and maintain the correct cooling
airflow.
■
Slide the remote end of module into the runners and
push home firmly to connect to the backplane.
■
Secure the module with the screws provided.
Details of the permissible combinations of modules and
3Com products are given later in this user guide.
Connecting Cables
Connect the module output socket to the input of the unit
to which you wish to provide an alternative power source
using one of the special cables. Use a standard cable
(supplied with this module) to provide managed
redundancy or a special ‘Y’ cable (available from your
supplier) where full redundancy (resilience) is required.
Details of how to use the ‘Y’ cables are given on the guide
which accompanies the cables.
After installing the module, this guide should be stored
with your other 3Com user guides.
If the product you are connecting to the Power
Module does not have the auto-enable feature
(see
SuperStack II Advanced RPS User Guide
,
part number DUA1607-0AAA0X), ensure the
mains cable is removed from it before
attempting to connect it to the Advanced RPS.
!
!
!
