062119
228-1692 REV 9
11
KEPCO, INC.
131-38 SANFORD AVENUE
FLUSHING, NY. 11355 U.S.A.
TEL (718) 461-7000
FAX (718) 767-1102
www.kepcopower.com
email: [email protected]
ment or decrement the highlighted digit.
Pressing
ADJUST
while rotating adjusts the
least significant digit. If the output is on (unit
not in Standby) changes made using the
ADJUST
control are immediately applied to
the output.
•
For alphanumeric characters use multiple
presses of the number keys for letters or sym-
bols:
0
(space),
1
(+, –, /),
2
(ABC),
3
(DEF),
4
(GHI),
5
(JKL),
6
(MNO).
7
(PQRS),
8
(TUV),
9
(WXYZ). Use the
T
key to highlight the next character. As an alter-
native, the
U
or
Y
keys or
ADJUST
control
will scroll through numbers, and letters and
symbols. Use the
CLEAR
key to clear the
entire alphanumeric field and start over
3. Press
$
to apply the change and return to the
menu (to change another parameter, repeat steps
1 and 2). To abort (return to the menu without
applying the change), press
%
.
NOTE:Press
HELP
key for more information,
press
HELP
again to see multiple
screens; press
CLEAR
key to exit the
help screen.
ADJUSTING LCD BRIGHTNESS, CON-
TRAST AND BACKGROUND
From the power-
up screen, (Figure 5), press
#
twice to initiate con-
trast adjustment. The contrast gradually alternates
between light and dark. When the contrast is accept-
able, press
#
to apply the change and exit contrast
adjust. Use the
T
and
R
keys for fine adjustment of
contrast. Contrast can also be adjusted from the
power-up screen by pressing
#
once, then pressing
T
and
R
as needed for fine adjustment.
To change the background, press
#
from the power-
up screen, Highlight Background, press
!
, highlight
Black or White, then
$
to save. Press
$
exit and
save for power-up or
%
to apply the changes (without
saving for power-up) and exit.
ENABLING/DISABLING AUDIBLE BEEPS
From the power-up screen, press
#
, then modify the
setting. Even though audible beeps are set to off, the
beeps will still sound upon power-up or detection of a
power supply fault.
SETTING VOLTAGE OR CURRENT MODE
The BOP uses two separate channels, one to set out-
put voltage or current and one to set the corresponding
protection limit. The main channel is determined by the
MODE
key (in local mode) which alternately selects
either Voltage mode or Current mode or by SCPI com-
mand (in digital remote mode). The protection channel
is determined automatically by the main channel
selected. When Voltage mode is selected, the current
protection channel is active, and when Current mode is
selected, the Voltage protection channel is active.
PROGRAMMING VOLTAGE OR CURRENT
AND ASSOCIATED PROTECT LIMITS
From
the power-up screen the settable voltage/current
parameters are displayed at the bottom of the LCD
above the
HELP
message. Use
Y
or
U
to highlight
the main or protect channel.
1. To verify that the unit is configured for internal ref-
erences press
$
from the power-up screen and
verify that Reference Input and Protection Limit
are set to Internal, and External Mode is set to
Disable. If necessary to change a setting, use
Y
or
U
to highlight the parameter, and press
!
to
modify. Highlight the desired selection and press
$
to save, then press
$
to save for power-up
or
%
to exit. If analog programming is desired,
refer to Operator’s Manual.
2. Verify that the load type has been configured
properly to ensure that the unit behaves as
expected when the output is off (see “Max/Min
Setting Menu” on page 13 6 for details).
3. Press
MODE
key to select the main channel
(VOLTAGE or CURRENT); the associated PRO-
TECT channel is automatically selected and dis-
played.
4. Set the output on or off as desired using the
STANDBY
key. The output is off (disabled) when
the
STANDBY
indicator is lit, on (enabled) when
not lit.
5. Use
Y
or
U
to highlight the main channel. There
are two ways to program the output in local mode.
These methods can be used either when the out-
put is disabled (
STANDBY
indicator lit) or
enabled.
WARNING
:
When the ADJUST control is
rotated, the active parameter is
immediately effective if the output
is enabled (on = STANDBY indica-
tor not lit). The voltage/current
applied to the load changes as the
ADJUST control is rotated.
•
Use the
ADJUST
control to increase or
decrease the main channel setting (e.g., volt-
age when the unit is in voltage mode). Start
with the most significant digit of the desired
value, then use
T
to highlight the next digit.
For fine adjustment press the
ADJUST
control
