062119
228-1692 REV 9
5
KEPCO, INC.
131-38 SANFORD AVENUE
FLUSHING, NY. 11355 U.S.A.
TEL (718) 461-7000
FAX (718) 767-1102
www.kepcopower.com
email: [email protected]
VII — ACCESSORIES.
See Table 5.
LOAD CONNECTIONS.
Power connections re-
quire wires that are properly rated for the nominal output
current of the unit. Connect the load to the OUTPUT
and COMMON power terminals on the rear panel (see
Figure 3). OUT S and COM S terminal of the Monitor
and Sensing Terminal block are for connection of
remote sensing leads (after removing the factory-
installed local sensing links).
NOTE: Output Sense lines must be connected for
proper operation, either locally, or at the load
(remote).
Also use OUT S and COM S to monitor volt-
age at the load using external equipment such as a
DVM, oscilloscope, etc. Use OUT MON and COM
MON to monitor voltage at the BOP output. Use twisted
wire pairs or wires that are tied together for both output
power and output sensing connections.
TABLE 5. ACCESSORIES
ITEM
FUNCTION
PART NUMBER
Line Cord (250V, 20A)
Provides connection to a-c mains via Nema 6-20P connector.
118-1087
Line Cord (250V, 20A)
Provides connection to a-c mains via Nema L6-20P locking type connector.
118-1088
Mating Connector, Trigger
Mates with Trigger port.
142-0527 (Kepco)
SP2501 (CUI Stack)
IEEE 1118 (BITBUS)
Mating connector
Allows connection to IEEE 1118 (BITBUS) port.
142-0485 (Kepco)
KMDLA-5P (Kycon Inc.)
IEEE 488 Cable, (1 meter long) For MG models only. Connects BOP power supply to GPIB bus.
SNC 488-1
IEEE 488 Cable, (2 meter long) For MG models only. Connects BOP power supply to GPIB bus.
SNC 488-2
IEEE 488 Cable, (4 meter
longs)
For MG models only. Connects BOP power supply to GPIB bus.
SNC 488-4
Interconnection Kits for parallel/
series configurations.
Cables required to connect multiple BOP models in parallel, series, or paral-
lel/series configurations.
See Operator’s Manual.
RS 232 Cable Kit
Contains RJ11 to RJ45 Patch cord, RJ 45 Patch cord, two RS 232 adapters,
one with male pins to connect to DTE equipment and one with female pins to
connect to a PC (personal computer), two RS 232 Loop Back test Connec-
tors (one 6-pin and one 8-pin) to test RS 232 communication and aid in iso-
lating RS 232 communication problems.
KIT 219-0436
RS 232 Adapter (Male pins)
Allows RS 232 port to be connected to DTE equipment. (Supplied in KIT
219-0436.)
142-0487
(L-COM RA098M)
RS 232 Adapter (Female pins)
Allows RS 232 port to be connected to a PC (personal computer). (Supplied
in KIT 219-0436.)
142-0506
(L-COM RA098F)
15-pin DSUB Connector
Mating connector for Analog input connector A2A5J6
Dsub 15 pin hood
Dsub 15 pin male
108-0374
(Tyco-Amp 207470-1)
142-0449
(Amphenol 17S-DA15P)
IDC 6-pin connector
Mating connector for RS-232 PORT, connector A1J5 and PROTECTION
EXT. PORT, connector A2A5J7
142-0536
(Amphenol 5-555176-3)
IDC 8-pin plug
Mating connector for PAR/SER PROTECT PORT (IN and OUT) connectors.
142-0535
(Amphenol 5-555176-3)
Slides
Allows easy withdrawal of unit from rack (see Figure 1). (Model CS 04
includes slides, brackets, all mounting hardware and installation instruc-
tions.)
CS 04
Heat Sink
Provides adequate cooling for calibration sense resistors.
136-0451
Output Terminal Cover
Protects against inadvertent contact with output and barrier strip terminals
129-0423
