manualshive.com logo in svg

Keofitt W9, User Manual, Page: 21 / 50

Share
Download
Keofitt W9 User Manual Download Page 21

KEOFITT W9 USER MANUAL V.4 

PAGE 21

5.2  Chemical disinfection

Immediately following the CIP, perform the disinfection, if required. The disinfection takes place with the 

valve remaining in its closed position.

There are 2 recommended ways to carry out the disinfection:

 

A) by letting the disinfectant flow through the valve chamber

 

B) by filling the valve chamber with the disinfectant (advantage: smaller volume of disinfectant 

needed and quicker and more reliable disinfection)

Steps to perform, when adopting A:

1. Connect a hose with an empty bottle to the lower hose piece. This 

bottle or similar recipient is to collect the disinfectant (step 3) and the 

rinsing water (step 6).

2. Fill a flexible bottle with the defined amount of disinfectant.
3. Connect the flexible bottle via a hose to the upper hose piece and 

press the disinfectant slowly through the valve to wet the interior of 

the valve.

4. Allow the disinfectant to act for the prescribed time.
5. Disconnect the hose from the upper hose piece and connect a flexible 

bottle with cleaned water to the upper hose piece.

6. Rinse through the upper hose piece by squeezing the bottle, thus 

pressing the water through the valve chamber.

7. Leave the squeezed bottle connected to the hose piece and clamp 

the hose to avoid contamination from air being sucked in through the 

valve.

Summary of Contents for W9



















































Reviews:

No comments