manualshive.com logo in svg

Keofitt W9, User Manual, Page: 20 / 50

Share
Download
Keofitt W9 User Manual Download Page 20

KEOFITT W9 USER MANUAL V.4 

PAGE 20

5.1  Chemical CIP

The CIP takes place with the valve remaining in its closed position.

Perform the following steps:

1. Remove the plugs.

(In the case of a valve with clamp connections there are no plugs 

supplied.)

2. Connect a water hose to the upper hose piece.

3. Connect a hose to the lower hose piece and let the hose go to a drain.

4. Flush with clean water.

5. Remove the water hose and let the CIP liquid flow through the upper 

hose piece. If the CIP liquid must not go to drain, circulate it or collect 

it in a suitable container and dispose of correctly.

6. Reconnect the water hose to the upper hose piece and rinse with 

clean water.

If disinfection is not needed the valve is now ready for taking a sample. If disinfection is required proceed 

with the steps mentioned in the section “Chemical disinfection” below.

Flush with clean water after sampling. If the process media is sticky, viscous or aggressive or for any 

other appropriate reason, do repeat the full CIP cycle after sampling. 

WARNING

•  Carefully follow the guidelines given for the chemicals involved 

•   Always remember to use safety goggles when steaming, CIPping, taking samples and all other 

operations of the sampling valve

Summary of Contents for W9



















































Reviews:

No comments