47
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Note:
◆
Skip steps 3 to 5 if you have already programmed the appropriate
CTCSS frequency.
◆
You can select a separate tone frequency for the CTCSS and Tone
functions.
◆
You cannot use the CTCSS and Tone functions simultaneously.
◆
If you select a high tone frequency, receiving audio or noise that
contains the same frequency portions may cause CTCSS to function
incorrectly. To prevent noise from causing this problem, select an
appropriate noise squelch level {page 15}.
Note:
Use Nos. 01 to 38, shown in the table above, when selecting tone
frequencies via Keypad Direct Entry {page 55} (U.S.A./ Canada only).
■
Automatic Tone Frequency ID
This function automatically identifies the incoming
tone frequency on a received signal.
1
Select the desired band.
2
Press
[TONE] (1 s)
to activate the function.
• The current tone frequency appears and the 1 Hz
decimal blinks.
• When a signal is received, the transceiver begins
scanning through all tone frequencies in order to
identify the incoming tone frequency.
• When the tone frequency is identified, the identified
frequency appears and blinks.
• The identified frequency is programmed in place of
the currently set CTCSS frequency.
3
Press any key to quit the function.
Note:
Received signals are audible while scanning is in progress.
1 s
.
o
N
.
q
e
r
F
)
z
H
(
.
o
N
.
q
e
r
F
)
z
H
(
.
o
N
.
q
e
r
F
)
z
H
(
.
o
N
.
q
e
r
F
)
z
H
(
1
0
0
.
7
6
1
1
4
.
7
9
1
2
5
.
6
3
1
1
3
8
.
2
9
1
2
0
9
.
1
7
2
1
0
.
0
0
1
2
2
3
.
1
4
1
2
3
5
.
3
0
2
3
0
4
.
4
7
3
1
5
.
3
0
1
3
2
2
.
6
4
1
3
3
7
.
0
1
2
4
0
0
.
7
7
4
1
2
.
7
0
1
4
2
4
.
1
5
1
4
3
1
.
8
1
2
5
0
7
.
9
7
5
1
9
.
0
1
1
5
2
7
.
6
5
1
5
3
7
.
5
2
2
6
0
5
.
2
8
6
1
8
.
4
1
1
6
2
2
.
2
6
1
6
3
6
.
3
3
2
7
0
4
.
5
8
7
1
8
.
8
1
1
7
2
9
.
7
6
1
7
3
8
.
1
4
2
8
0
5
.
8
8
8
1
0
.
3
2
1
8
2
8
.
3
7
1
8
3
3
.
0
5
2
9
0
5
.
1
9
9
1
3
.
7
2
1
9
2
9
.
9
7
1
0
1
8
.
4
9
0
2
8
.
1
3
1
0
3
2
.
6
8
1
Summary of Contents for TM-G707
Page 84: ......
