Kenwood NX-5900 Service Manual Download Page 83

Page: 83 / 120

(No.RA032<Rev.001>)1-83

5.3

Failure diagnosis of the Bluetooth section

Over view:

When the Bluetooth function does not operate, use this flowchart to determine the problem.

I can not pair with the Bluetooth (BT) headset.

When an abnormal
condition is confirmed.

Major parts for a Bluetooth circuit

Bluetooth antenna (Pattern Antenna)
LC filter (L11)
Bluetooth/GPS (IC5)
Level conversion IC (IC6, IC7)
TCXO 19.2MHz (X1)
32.768kHz clock (X2)
33BT Regulator (IC3)
18BT Regulator (IC2)
MPU/DSP IC (IC706)

Replace any abnormal parts.

Verify the BT/GPS power supply.
(33BT) L4: 3.3V

Check the Module (BT/GPS) unit PCB side A.

Verify the ANT Matching Parts.
Visual check of L15, C68
(Whether not damaged)

[The BT/GPS power supply
line 33BT circuit is faulty]

L4, C15, C19, C20, C33
Replace any abnormal parts.

Check the Module (BT/GPS) unit
PCB side B (a).

Verify the BT/GPS power supply.
(18BT) L15: 1.8V

[The BT/GPS power supply
line 18BT circuit is faulty]

C18, C13, C31, L8, C39

Check the Module (BT/GPS) unit
PCB side B (b).

Verify the RTC for the BT/GPS.
X2 (3 pin): Square waveform,
32.768kHz,1.8Vp-p

Make sure the BT headset have enough power?
Turn on your BT headset?
Put your BT headset into pairing mode?

Charge the BT headset. Turn on your BT headset and bring it
within one to two meters.
Try again pair with BT headset.

IC706

IC6

IC5

UART

L11

IC7

Pattern Antenna

PCM

MAIN UNIT

MODULE (BT/GPS)
UNIT

MPU/DSP

BT/GPS

TCXO

19.2MHz

32.768kHz

Clock

Filt er

Bluet oot h

Ant enna

Level

conversion

Level

conversion

When a normal
condition is confirmed.

Replace any abnormal parts.

Verify the RTC Line circuit for
the BT/GPS.
Visual check of X2, L8, C39
(Whether not damaged)
Replace any abnormal parts.

Visual check of

the PCB side A parts.

Visual check of

the PCB side A parts.

(Whether not damaged)

Summary of Contents for NX-5900

























































































































Search results

Summary of Contents for NX-5900

Reviews:

Related manuals for NX-5900

Brands by name

Popular brands

Kenwood NX-5900, Service Manual

Search results

Summary of Contents for NX-5900

Reviews:

Related manuals for NX-5900

Brands by name

Popular brands