Kenwood NX-5900 Service Manual Download Page 42

Page: 42 / 120

1-42 (No.RA032<Rev.001>)

4.4

BER (Bit Error Rate) Measurement

(1) The Panel Test Mode is used to measure the BER (Refer

"4.2.1 Test mode operation features").

(2) Select "10" (P25 Phase1), "7" (P25 Phase2) and "7"

(NXDN Mode) for test signaling (Refer to "4.2.3 Frequency
and Signaling" (2) Test signaling).

Note:

"7" (NXDN Mode) can be selected only by PC test mode.

(3) Select a bandwidth (Narrow/Very Narrow) by pressing the

[

] key. When P25 Phase1 or P25 Phase2 is selected, it

is not necessary to select a bandwidth.

(4) Select a test frequency ("4.2.3 Frequency and Signaling"

(2) Test signaling Test frequency).

(5) Measure the BER (Bit Error Rate) using the digital radio

tester.
Enter a standard input signal into the transceiver as a stan-
dard tone test pattern for P25, FSW+PN9 for NXDN.

(6) Adjust the input signal level to achieve the standard bit er-

ror rate (BER).

(For example, if the BER is 0.86%, the display shows
"0.86".)

4.5

Adjustment points

4.6

Test Equipment Required for Alignment

*The test equipment which is not used for adjustment is contained in this table.

MAIN UNIT (XC1-1021-80) (A/2)
Component side

RTC

Test Equipment

Major Specifications

1. Standard Signal
Generator (SSG)

Frequency Range
Modulation
Output

100 to 900MHz
Frequency modulation and external modulation
-127dBm/0.1uV to greater than -20dBm/22.4mV

When performing the Frequency adjustment, the following accuracy is necessary.
• 0.001ppm
Use a standard oscillator for adjustments, if necessary.

2. Power Meter

Input Impedance
Operation Frequency
Measurement Capability

Ω

100 to 900MHz
Vicinity of 100W

3. Deviation Meter

Frequency Range

100 to 900MHz

4. Digital Volt Meter
(DVM)

Measuring Range
Input Impedance

10mV to 20V DC
High input impedance for minimum circuit loading

5. Oscilloscope

DC through 30MHz

6. Frequency Counter

Frequency Range
Frequency Stability

10Hz to 1000MHz
0.2ppm or less

To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz for
RTC Correction Resolution 0.01Hz is better for accuracy adjustment.

7. Ammeter

20A or more

8. AF Volt Meter (AF VM)

Frequency Range
Voltage Range

50Hz to 10kHz
1mV to 10V

9. Audio Generator (AG)

Frequency Range
Output

50Hz to 5kHz or more
0 to 1V

10. Distortion Meter

Capability
Input Level

3% or less at 1kHz
50mV to 10Vrms

11. Spectrum Analyzer

Measuring Range

DC to 1GHz or more

12. 4

Ω

Dummy Load

Approx. 4

Ω

, 10W

13. Regulated Power Supply

13.6V, approx. 20A (adjustable from 9V to 17V)
Useful if ammeter equipped

Summary of Contents for NX-5900

























































































































Search results

Summary of Contents for NX-5900

Reviews:

Related manuals for NX-5900

Brands by name

Popular brands

Kenwood NX-5900, Service Manual

Search results

Summary of Contents for NX-5900

Reviews:

Related manuals for NX-5900

Brands by name

Popular brands