Kenwood NX-5900 Service Manual Download Page 13

Page: 13 / 120

(No.RA032<Rev.001>)1-13

2.3.2 Horn Alert/P.A. Relay Unit (KAP-2: Option)

The Horn alert (max. 2A drive), Public address and External
speaker function are enabled by installing the KAP-2 in the trans-
ceiver.

2.3.2.1

Installing the KAP-2 unit in the transceiver
(The kit A is not used in the KAP-2 accessories)

(1) Remove the cabinet, top packing and shielding plate of the

transceiver.

(2) Set the KAP-2 relay unit jumper pins according to the pur-

pose of use.

(3) Remove the 6-pin jumper connector inserted in the TXRX

unit (A/2) connector (CN910). <1>

Fig.2-1

(4) Insert one side of the lead wire with connector (E37-1114-

05) into the relay unit connector (CN3) <2> and the other
side into the TX-RX unit (A/2) connector (CN910) <3>

Fig.2-2

(5) Place the relay unit at the position shown in Figure 2-2 and

secure it to the chassis with a screw.

(6) Remove the cap on the rear of the chassis by pushing it

from the inside with your finger. <4>

Fig.2-3

(7) Pass the 6-pin connector of the cable (E37-1113-25)

through the chassis hole <5> and insert the bush into the
shassis hole.

(8) Rotate the bush of the cable 90 degrees counterclockwise

as viewed from the rear of the chassis. <6>

(9) Insert the 6-pin connector of the cable into the connector

(CN2) of the KAP-2 relay unit. <7>

Note:

You must setup using the KPG-D1/D1N.

Fig.2-4

(10) Form the KAP-2 cable as shown in the figure.

CN910

<1>

E37-1114-05

CN910

CN3

<2>

<3>

<4>

<5>

E37-1113-25

CN2

<7>

<6>

KAP-2 cable

Summary of Contents for NX-5900

























































































































Search results

Summary of Contents for NX-5900

Reviews:

Related manuals for NX-5900

Brands by name

Popular brands

Kenwood NX-5900, Service Manual

Search results

Summary of Contents for NX-5900

Reviews:

Related manuals for NX-5900

Brands by name

Popular brands