TK-5810
(
BG
)
/5810H
(
BG
)
15
3. Dual Control Head Remote Kit
(KRK-6DH: Option)
The KRK-6DH remote kit connects two displays (two
KCH-14s or KCH-15s) to the transceiver. The KRK-6DH is
connected to the KCH-14s or KCH-15s with two optional
control cables. There are three version of the control cable:
KCT-22M (8 feet), KCT-22M2 (17 feet), and KCT-22M3 (25
feet).
3-1. Installing the KRK-6DH main panel onto the
transceiver
1. Remove the upper case and lower case of the transceiv-
er.
2. Insert the lead wire with connector (W700) of the control
unit (X53-440) into the connector (CN4) of the KRK-6DH.
Insert the lead wire with connector (W104) of the KRK-
6DH into the connector (CN503) of the transceiver.
3. Install the KRK-6DH main panel on the transceiver using
four screws
q
.
Note:
Take care that the lead wire with connector (W700) is
not caught when fi tting the KRK-6DH main panel on the
transceiver.
4. Affixing the sheet (G11-4379-04) for the waterproof
(Fig.3-1-2).
(1) Remove the covering paper of the sheet
w
.
(2)
Affi x the sheet while taking note of the position of the
three parts as shown in Fig.3-1-2
e
.
Firmly
affi x the sheet to the chassis by pushing the
double-coated tape with your fi ngers.
(3) Repeat step (2) to affi x the sheet to the other side of
chassis.
Note:
The sheet cannot be reused. Affix a new sheet when
you removed the sheet.
5. Reassemble the upper case and lower case of the trans-
ceiver. (Refer to page 18)
Note:
Take care that the sheet (G11-4379-04) is not peeled off
when installing the upper/lower case.
KRK-6DH
main panel
W700
CN4
CN5
W104
CN503
Transceiver
:
:
Fig. 3-1-1
Affix the sheet while
taking note of the position
of the three parts.
KRK-6DH main panel
@
.
Fig. 3-1-2
3-2. Installing two KRK-6DH rear panels onto two
front panel kits
Install each KRK-6DH rear panel onto each front panel
kit as same as “2-2.Install the KRK-5 rear panel onto the
front panel kit” described on page 14.
3-3. Control cable (KCT-22) connection (Fig. 3-2)
1. Use two control cables. Insert one connector of the one
control cable to the transceiver (with KRK-6DH) and the
other to the display 1.
Insert one connector of the other control cable to the
transceiver (with KRK-6DH) and the other to the display 2.
Connect each cable to the GND terminal with the screws
q
supplied with each control cable.
2. Secure the one connector of each control cable to the
KRK-6DH main panel with two screws
w
according to
the installation condition of the transceiver. Pass the con-
trol cables through the grooves at both ends of the KRK-
6DH main panel and secure the control cables to the
KRK-6DH with the cable fitting (J21-4354-04) and two
screws
e
supplied with the KRK-6DH.
3. Secure the other connectors of the control cables to the
display 1 and display 2 with two screws
r
in the same
way.
INSTALLATION
