Kendrion Kuhnke FIO AI4 Instruction Manual Download Page 117

Page: 117 / 195

Kendrion Kuhnke Automation GmbH

AO4 U/I

– 16-Bit

(E 747GB-V2)

117

28. January 2020

Status LEDs

LED "EtherCAT Run"

The LED labelled "EtherCAT Run" indicates the state of the EtherCAT ASIC.

Initialising, no data exchange

Pre-Op

Off/green, 1:1

Pre-operational, no data exchange

Safe-Op

Off/green, 5:1

Safe operation, inputs readable

Green, on

Operational, unrestricted data exchange

LED "IO"

The LED labelled "IO" indicates the state of the module's I/Os.

State

LED flash code

Explanation

Green, on

No error

Error

Off

Malfunction of module if E-bus LED = On

Inoperative if E-bus LED = Off

Red, 1x

Short circuit

Red, 2x

Low voltage

Red, 4x

EtherCAT watchdog control

Red, 6x

Module-specific fault

Red, 7x

Configuration error (E-bus pre-operational), no. of
process data differs from that in the module

Defective

Red, on

Module defective

LED "Power"

The LED labelled "Power" indicates the state of the I/O module's I/O power supply.

State

LED flash code

Explanation

Green, on

24 VDC supply ok

Off

24 VDC supply not ok

LEDs "Channel"

The "Channel" LEDs indicate the state of every channel.

State

LED flash code

Explanation

Green, on

Channel enabled

Off

Channel disabled

Error

Red, 1x

Short circuit

Red, 3x

Wire failure

Red, 5x

Excessive temp. of output drivers

Summary of Contents for Kuhnke FIO AI4




































































































































































































Search results

Summary of Contents for Kuhnke FIO AI4

Reviews:

Related manuals for Kuhnke FIO AI4

Brands by name

Popular brands

Kendrion Kuhnke FIO AI4, Instruction Manual

Search results

Summary of Contents for Kuhnke FIO AI4

Reviews:

Related manuals for Kuhnke FIO AI4

Brands by name

Popular brands