KEM MKC-710 Operation Manual Download Page 84

Page: 84 / 133

6. Setup

6-1-2.Date acquisition software (SOFT-CAP)

The optional software SOFT-CAP is Windows

-based application and can download the

measurement data to Microsoft

Excel

workbook or store in CSV format through

RS232C port.
By this software, starting titration or reset can be commanded by the computer.

＜

Receiving date

＞

The SOFT-CAP software can export the measurement results as follows:

1) It transfers the data to Microsoft

Excel

workbook.

2) It stores the data in CSV format so that spreadsheet can be used.

＜

Sending date

＞

The personal computer can send commands including titration start and reset.

Note

For details, see the operation manual for Data Acquisition Software (SOFT-CAP).

6-1-3.Printer setting

<IDP-100>
Connect the IDP-100 to COM1.

<DP-600>
Connect the DP-600 to the USB port.

Select “2

．

Printer” with [

↑

][

↓

] and press [ENTER].

Summary of Contents for MKC-710






































































































































Search results

Summary of Contents for MKC-710

Reviews:

Related manuals for MKC-710

Brands by name

Popular brands

KEM MKC-710, Operation Manual

Search results

Summary of Contents for MKC-710

Reviews:

Related manuals for MKC-710

Brands by name

Popular brands