KEM MKC-710 Operation Manual Download Page 36 | Manualshive

Page: 36 / 133

background image

3. Basic operation

26

Note

Do not use the Auto Solvent Change Unit for those samples which are hard to
dissolve or insoluble in solvent in order to avoid clogging of drain tube. Such
waste liquids, if spilled, after measurement may corrode the tube connectors
causing the Auto Solvent Change Unit malfunction.

Note

Change the connecting of the Auto Solvent Change Unit for those samples

which are oily in order to avoid damage of drain tube.

＜

Drain

＞

1)

Press Drain Pump [On] key to drain
waste liquid.

«
...
34
35
36
37
38
...
»

Summary of Contents for MKC-710






































































































































Reviews:

No comments

Related manuals for MKC-710

Brand: Teac Pages: 148

Brand: IFM Pages: 25

Brand: Campbell Pages: 16

MIC TRAC MT-3000

Brand: GAGEMAKER Pages: 20

Brand: MadMan Pages: 37

Brand: MADDALENA Pages: 5

Brand: Make Noise Pages: 15

Brand: Major tech Pages: 40

Brand: PASCO Pages: 3

Brand: PASCO Pages: 2

Brand: NanoPhotometer Pages: 133

Brand: ISKRAEMECO Pages: 12

RAVTD1760WS Series

Brand: Ravaglioli Pages: 24

SF6 Portable Monitor

Brand: Bacharach Pages: 2

Brand: Kobold Pages: 19

Brand: Kane Pages: 52

Brand: E+E Elektronik Pages: 48

Brand: Extech Instruments Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands