KBC WESII Series User Manual Download Page 135 | Manualshive

Page: 135 / 141

background image

WESII User Manual

Manual-WESII-Rev1403
Copyright © KBC Networks 2014

Page 134 of 140

www.kbcnetworks.com

11.2.7 Advanced Wireless Configuration: Radio 1

This section can be used to alter the long range parameters of the link, this is necessary
for wireless link lengths exceeding 1.6km/1 mile and also to alter the value of the signal
strengths of the RSSI LEDs located on the back of the WESII units.

Long Range Parameters

It is recommended that for all links over 1.6km (1mile) the long range parameters must
be set. In the example below, the WESII is configured for a 1600m (1 mile) connection.
Both the Host/AP and Client units must be configured for the distance parameters:

«
...
133
134
135
136
137
...
»

Summary of Contents for WESII Series














































































































































Reviews:

No comments

Related manuals for WESII Series

Brand: IBM Pages: 86

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

SATA II ExpressCard 34

Brand: LaCie Pages: 2

12big Rack Fibre 8

Brand: LaCie Pages: 9

Brand: Paradyne Pages: 112

Brand: Cambium Networks Pages: 215

RIPWAVE 40-00460-00R

Brand: Navini Networks Pages: 35

Brand: Hama Pages: 8

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

Brand: Barco Pages: 121

Brand: SyChip Pages: 24

Brand: Seattle Computer Products Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands