KaVo HealOzone 2130 C Instructions For Use Manual Download Page 56

Page: 56 / 61

Instructions for use HealOzone 2130 C
8 Troubleshooting

8.2 Error Messages

Malfunction

Cause

Remedy

ERROR_OG_SW

Ozone generator switch function

faulty.

▶ Inform technical service.

ERROR_OG_PWM

Ozone generator desired value faul‐

ty.

▶ Inform technical service.

ERROR_OG_I_MAX

Max. ozone generator power con‐

sumption level exceeded.

▶ Inform technical service.

ERROR_OG_I_MIN

Ozone generator power consumpti‐

on below minimum level.

ERROR_PUMPE_SW

Pump switch function faulty.

▶ Inform technical service.

ERROR_PUMPE_I_MAX

Max. pump power consumption le‐

vel exceeded.

▶ Inform technical service.

ERROR_PUMPE_I_MIN

Pump power consumption below

minimum level.

▶ Inform technical service.

ERROR_LUEFTER_SW

Ventilator switch function faulty.

▶ Inform technical service.

ERROR_LUEFTER_I_MAX

Max. ventilator power consumption

level exceeded.

▶ Inform technical service.

ERROR_LUEFTER_I_MIN

Ventilator power consumption be‐

low minimum level.

▶ Inform technical service.

ERROR_EE_READ

EEPROM data read error.

▶ Inform technical service.

ERROR_EE_WRITE

EEPROM write error.

▶ Inform technical service.

ERROR_EE_ACK

EEPROM communication error.

▶ Inform technical service.

ERROR_EE_ABGLEICH

EEPROM calibration data error.

▶ Inform technical service.

ERROR_EE_SETUP

EEPROM setup data error.

▶ Inform technical service.

ERROR_EE_BETRIEB

Operating data in EEPROM faulty.

▶ Inform technical service.

ERROR_EE_BEHANDLUNG

Handling data in EEPROM faulty.

▶ Inform technical service.

54/57

Summary of Contents for HealOzone 2130 C






























































Search results

Summary of Contents for HealOzone 2130 C

Reviews:

Related manuals for HealOzone 2130 C

Brands by name

Popular brands

KaVo HealOzone 2130 C, Instructions For Use Manual

Search results

Summary of Contents for HealOzone 2130 C

Reviews:

Related manuals for HealOzone 2130 C

Brands by name

Popular brands