KaVo HealOzone 2130 C Instructions For Use Manual Download Page 37

Page: 37 / 61

Instructions for use HealOzone 2130 C
5 Operation

5.2 The treatment procedure

If the measured moisture level lies above the range of the assigned moisture level,

this status is shown in the display.

The start of drying is reported acoustically by a double buzzer tone.

▪ Treatment time

▪ Drying process running

If the flow sensor becomes inactive during the drying process, the unit displays

message "Waiting for treatment". You can choose the Stop button to cancel and it

will switch directly to rinse mode.

5.2.8 Treatment

An airtight seal has been created. Ozone is produced from this point on. The unit

counts down the seconds for the remainder of the treatment time. Once the treat‐

ment time has come to an end, the unit switches to rinse mode. It is no longer

possible to change the treatment time.

You can press the stop button or the footswitch to stop the process. If the process

is stopped, the unit switches directly to rinse mode.

Screen information:

▪ Remaining treatment time

▪ Ozone application

5.2.9 Ozone generation

If it takes a while to generate ozone, "Generate ozone" is shown on the display and

reported acoustically with a double buzzer tone.

Screen information:

▪ Treatment time

▪ Ozone is being generated

Once the ozone starts being generated, the device switches immediately to treat‐

ment status.

If ozone cannot be generated within 60 seconds, the warning "Ozone generation

not successful" is output.

The message can be acknowledged with any button, and the treatment process can

be restarted.

5.2.10 Vacuum lost

If the airtight seal over the tooth is broken during treatment, ozone production is

stopped and air is blown through the ducts to clear them. The unit waits until the

vacuum has been recreated. The "Seal cup" line starts flashing. The treatment time

cannot be changed. If the airtight seal cannot be recreated within 60 seconds, treat‐

ment is cancelled. A warning message appears on screen. To stop the process,

press the stop button or footswitch. If you do this, the unit switches directly to rinse

mode.

35/57

Summary of Contents for HealOzone 2130 C






























































Search results

Summary of Contents for HealOzone 2130 C

Reviews:

Related manuals for HealOzone 2130 C

Brands by name

Popular brands

KaVo HealOzone 2130 C, Instructions For Use Manual

Search results

Summary of Contents for HealOzone 2130 C

Reviews:

Related manuals for HealOzone 2130 C

Brands by name

Popular brands