KaVo HealOzone 2130 C Instructions For Use Manual Download Page 57

Page: 57 / 61

Instructions for use HealOzone 2130 C
9 Safety checks

9.1 Basics

9 Safety checks

9.1 Basics

Note

You are required to comply with all safety information provided in the User instruc‐

tions under section 2 Safety.

According to VDE 0751-1:

▪ Safety checks every two years

▪ Device type IIa

▪ Protection class I

▪ Portable device

▪ Type B general

▪ Measurement in accordance with EGA

KaVo supplies a medical device record in which you make an inventory listing and

record the main master data of the medical device. www.kavo.com/De/produkte/

praxis_einrichtungen/

The following readings and measurements must be documented:

▪ Visual inspection of medical device and accessories

▪ Nominal data checks on externally accessible fuses.

▪ Earthed conductor checks in accordance with VDE 0751

▪ Leakage current measurements in accordance with VDE 0751

▪ Functional test of the medical device taking into account accompanying docu‐

ments

Note

The main unit switch must be switched on during measurement.

55/57

Summary of Contents for HealOzone 2130 C






























































Search results

Summary of Contents for HealOzone 2130 C

Reviews:

Related manuals for HealOzone 2130 C

Brands by name

Popular brands

KaVo HealOzone 2130 C, Instructions For Use Manual

Search results

Summary of Contents for HealOzone 2130 C

Reviews:

Related manuals for HealOzone 2130 C

Brands by name

Popular brands