background image

32 / 44 

Installing the CAP Converter on the Rear Panel of a TV Set

Danger to life due to high voltage!

Screws that are screwed in too deeply may damage the TV set beyond repair and cause danger to life 

through electric shock.

Before starting any installation work, disconnect all units from the mains.

Before installing the CAP converter, check with the manufacturer of the device or in the documentation 

supplied with it whether this is permissible, and if so, what aids (screws, etc.) are necessary or can be 

used.

Material damage and risk of injuries due to overheating of the devices and fi re!

Do not install the CAP converter between a TV set and a wall bracket.

Only install the CAP converter on the rear panel of a TV set if the TV sits on a stand that is fi xed some-

where else.

Only two screws are required to secure the CAP converter to the rear panel of the TV set. Before installing the CAP 

converter, note the following:

The TV set must have one of the following hole patterns for wall brackets on its rear panel: 100 x 100; 100 x 200; 200 x 

200 or 200 x 400. If this is not the case, a VESA adaptor plate can be obtained from a specialist dealer.

Before mounting the CAP converter, read the chapter on wall mounting in the operating manual of your TV set to fi nd 

out about the screw diameter (M4, M6 or M8) and the permitted screw-in depth.

 Connecting the CAP Converter

    

The CAP converter may only be operated with a supply voltage of 10.5 - 30.0 V. The earth connection of the 

CAP converter must be connected to the negative pole of the motor home or caravan battery. Disconnect 

the vehicle electrical system (main switch “off “ or disconnect the positive pole from the vehicle electrical 

system battery) before starting the following work.

Connect the master coaxial cable (coming from the turntable) to the F socket “IF Input“, on newer units “Antenna“, at 

the rear of the CAP converter.

Connect the “IF Output“ socket, on newer units “TV/STB“, of the CAP converter and a receiver or TV set with integ-

rated tuner to a coaxial cable.

Connect the supplied power cable (depending on the power supply available in your motor home or caravan, 12 V or 

230 V with mains adapter) to the “12 V 2.0 A“ plug-in connection of the CAP converter.

Check the connections before you reconnect the on-board power supply.

Connections on the CAP converter

RESET

TV/STB

ANTENNA

-

+

12V      2,0A

ETHERNET

STATUS

CONTROL UNIT

950-2150MHz

14/18V 

400mA max.

22kHz

DE - 83022 Rosenheim

USB 2.0

5V        500mA max.

1

2

3

4

5

6

7 8

9

TV/STB 

 

Output satellite signal to TV/receiver

 ANTENNA   

Input satellite signal from the turntable

 RESET 

 

Reset button

 USB 2.0 

 

Type A USB port

 ETHERNET   

Network socket, RJ 45

 CONTROL UNIT 

Connection for push-button/HDS 50/HDS 52, RJ 12

 STATUS 

 

Status LED to indicate the operating status

 Power switch

 12 V   2.0 A   

Power supply

Summary of Contents for 203500001













































Reviews: