– 6
Illustrations on Page 2
Illustration
Unscrew the safety lock and fill the steam cleaner
with a max. of 1 litre of water.
Illustration
Screw in safety cap.
Illustration
Plug in the mains plug.
The green and orange indicator lights are on.
Illustration
Wait until the orange indicator lamp goes out.
Illustration
Connect the accessories to the steam gun.
The steam cleaner is ready to use.
Illustration
Insert steering roller and transport wheels and lock
them.
Illustration
Connect the required accessories (see Chapter
"How to use the accessories“) to the steam gun. In-
sert the open end of the accessory on the steam
gun and push onto the steam gun until the unlock-
ing button of the steam gun locks into place.
Illustration
Use the extension tubes if necessary. To do so,
connect one or both extension tubes to the steam
gun. Insert the required accessories on the free
end of the extension tube.
Move the selector switch for the steam volume
back (steam lever locked).
Illustration
To detach the accessory parts, press the unlocking
button and pull the items apart.
Notes
In case of continuous use of commercially available
distilled water, no descaling of the boiler is neces-
sary.
You can reduce the heating-up time by using warm
water.
Remove the safety lock from the device.
Illustration
Completely empty the steam boiler to remove exist-
ing water.
Fill the boiler with a maximum of 1 liters of fresh tap
water.
Screw the safety cap back onto the device.
Place the unit securely on a firm surface.
Insert the mains plug into a socket.
Both indicator lamps must illuminate.
The orange indicator lamp goes out after approxi-
mately 8 minutes.
The steam cleaner is ready to use.
Use the selector switch for the steam volume to regulate
the discharged steam. The selector switch has three po-
sitions:
Set selector switch to the required steam volume.
While operating the steam switch, always direct the
steam gun at a separate piece of cloth until the
steam is emitted evenly.
Note:
The heating of the steam cleaner is turned on in
regular intervals during the operation of the appli-
ance in order to maintain the pressure in the boiler
at a constant level. When the heating is turned on,
the orange indicator lamp (heater) lights up.
Water needs to be filled into the boiler, if the steam vol-
ume decreases during work and no more steam is emit-
ted in the end.
Disconnect the mains plug from the socket.
Push the steam switch until steam discharge stops.
Now, the boiler of the appliance is unpressurized.
Remove the safety lock from the device.
Fill the boiler with a maximum of 1 liters of fresh tap
water.
Screw the safety cap back onto the device.
Insert the mains plug into a socket.
The orange indicator lamp goes out after approxi-
mately 8 minutes.
The steam cleaner is ready to use.
Illustration
Disconnect the mains plug from the socket.
Illustration
Push the steam switch until steam discharge stops.
Now, the boiler of the appliance is unpressurized.
Illustration
Put the extension pipes into the large accessory
compartments.
Insert the manual nozzle and detail nozzle onto
each extension pipe.
Attach the big round brush to the small detail nozzle.
Put the small round brush and nozzles into the me-
dium accessory compartment.
Hook the floor nozzle into the parking position.
E2 Unlocking button
F1 Floor nozzle
F2 Retaining clip
F3 Terry floor cloth
F4 Microfibre floor cloth
G1 Decalcifying sticks
Quick Reference
Operation
Attaching the Accessories
Removing the Accessories
Fill up with water
Turning on the Appliance
Adjusting the Steam Quantity
Maximum steam volume
Reduced steam volume
No steam - child protection
Note:
In this lever position, the steam lever cannot be
used.
Refilling Water
Turning Off the Appliance
Storing the Appliance
11
EN
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
