Kärcher SC 2 Operating Instruction Download Page 12

Page: 12 / 138

– 7



Wrap the steam hose around the extension pipes
and insert the steam pistol into the floor nozzle.

It is recommended to sweep or vacuum the floor prior
to using the steam cleaner. This way, the floor is already
cleared of dirt/loose particles prior to the wet cleaning.

Prior to treatment with the steam cleaner, always check
the reaction of the textiles in an inconspicuous location:
Steam at first, then let dry and then check for colour or
shape changes.

When cleaning painted or plastic-coated surfaces, as
found on kitchen and living room furniture, doors, par-
quet; wax, furniture polish, plastic surfaces or paint can
come loose or stains can be created. When cleaning
these surfaces, briefly steam a cloth and wipe the sur-
faces with it.

ATTENTION

Never direct the steam jet at glued edges as the edge
band may loosen. Do not use the steam cleaner on un-
sealed wooden or parquet floors.

In case of low outside temperatures, especially in the
winter, warm up the window pane by slightly steaming
the entire glass surface. This will prevent tensions on
the surface which might lead to glass breakage.
Then clean the window surface with the hand nozzle
and attachment. Use a squeegee to remove the water
or wipe the surfaces dry.

ATTENTION

Do not direct steam onto the sealed locations of the win-
dow frame to prevent damage.

You can use the steam gun without any additional ac-
cessories, e.g.:
–

to remove light wrinkles from hanging clothes by
steaming them at a distance of 10 to 20 cm.

–

to remove dust from plants. Here, keep a distance
of 20-40 cm.

–

for moist dusting, by briefly steaming the cloth and
wiping the furniture with it.

Illustration



Install detail nozzle on the steam gun.

The closer this nozzle is to the contaminated area, the
higher the cleaning effect, as the temperature and the
steam are highest at the nozzle output. Especially suit-
ed for cleaning difficult access locations, joints, fittings,
drains, sinks, toilets, blinds and heaters. Heavy lime
scale can be drenched in vinegar prior to steam-clean-
ing. Let the vinegar penetrate for about 5 minutes.

The round brush can be installed onto the detail nozzle
as an accessory. Attached brushes can therefore be
used to remove heavy soiling.

ATTENTION

Not suitable for cleaning sensitive surfaces.

Illustration



Attach the round brush to the detail nozzle.

The power nozzle can be installed onto the detail nozzle
as an accessory.
The power nozzle increases the emission speed of the
steam. Therefore, it is well-suited for cleaning very
tough dirt, blowing out corners, grooves, etc.
Illustration



Attach the power nozzle to the detail nozzle ac-
cording to the round brush.

The round brush can be installed onto the detail nozzle
as an accessory. This round brush allows to clean large
rounded surfaces (e.g. sink, shower tray, bathtub, kitch-
en sink).

ATTENTION

Not suitable for cleaning sensitive surfaces.

Illustration



Attach the round brush to the detail nozzle.

Illustration



Install hand nozzle on steam gun.

Pull the cloth cover over the hand nozzle. Especially
well-suited for small washable areas, shower stalls and
mirrors.

Suited for all washable walls and floor coverings, e.g.
stone floors, tiles and PVC floors. Work slowly on very
dirty surfaces to allow the steam to act on the dirt for a
longer period of time.

Note

Detergent residue or care emulsions that are still pre-
sent on the surface to be cleaned can lead to streaks
during steam cleaning. However, these will disappear
with repeated cleaning procedures.
Illustration



Attach the floor cloth to the floor nozzle.

–

Place the floor nozzle on top of the floor cloth.
Depending on model - fold bevore the floor cloth
the long way.

–

Open holding clamps.

–

Place the cloth ends into the openings and pull
them tight.

–

Close the holding clamps.

몇

CAUTION