![background image](http://html1.mh-extra.com/html/karcher/kmr-1000-t/kmr-1000-t_operating-instructions-manual_3632794023.webp)
English
KMR 1000 T
23
Let down the main brush.
♦
Pay attention to the position of the
bristle set when installing the new
main brush!
!
Slide the main brush in the
receptacle on both sides, and
secure it using a flat washer and
screw.
♦
Note the correct position of the flat
washer, it must overlap the main
brush on the driver from both sides.
!
Take the sweeper down from the
drive ramps
!
Check the main brush pattern and
position
!
Screw on covers
!
Insert the swept material container
Check and adjust sweeping range
of roller
!
Check the tyre air pressure
!
Raise the sweep roller
!
Raise the side broom
!
Pull and hold the coarse-dirt flap.
!
Drive the sweeper on a flat and
smooth floor noticeably covered
with dust or chalk
!
Let down the coarse-dirt flap
!
Lower the main brush and let it
rotate approx. 30 s
!
Raise the sweep roller
!
Pull and hold the coarse-dirt flap
!
Back out in reverse
!
Check the sweep mirror
The form of the sweeping pattern
forms a regular rectangle that is less
than 50-70 mm wide
Adjusting the width of the sweep
mirror
Adjust bowden cable on both sides.
Sweeping pattern is not parallel
!
Lengthen the bowden cable on the
narrower side of the sweeping
pattern.
The sweeping pattern is too small
!
Lengthen the bowden cable on
both sides.
The sweeping pattern is too large
Notify Kärcher customer service
Change the sealing strip
!
Turn off machine and remove the
spark plug connector
!
Adjust "parking brake" operating
mode
!
Remove the swept material
container
Remove covers.
Remove covers.
Side sealing strips
!
Unscrew the fastening of the
sealing strip
!
Screw on a new sealing strip and
don’t tighten the screws yet
!
Slide under a support with 1-2 mm
thickness to adjust the ground
clearance
!
Align the sealing strip
!
Tighten the screws
Front sealing strip
!
Unscrew the fastening of the
sealing strip
!
Screw on a new sealing strip and
don’t tighten the screws yet
!
Align the sealing strip
!
Adjust the ground clearance of the
sealing strip such that there is a
spacing of 10-15 mm toward the
back
!
Tighten the screws
Summary of Contents for KMR 1000 T
