background image

8

Safety

WARNING: Protect machine from 
freezing.

AVERTISSEMENT: 

Protéger la 

machine contre le gel.

1.

To keep machine in best 
operating conditions, it is 
important you protect machine 
from freezing. Failure to protect 
machine from freezing could 

cause malfunction of the machine and result in 
death, serious bodily injury, and/or property 
damage. Follow storage instructions specified in 
this manual.

2.

Inlet water must be clean fresh water and no hotter 
then 90°F.

DANGER: Risk of asphyxiation. 
Do not inhale fumes. Use this 
product only in a well ventilated 
area. 

DANGER: 

Risque d'asphyxie: Ne 

pas inhaler les vapeurs. Utiliser 
ce produit uniquement dans un 
endroit bien ventilé.

3.

Running this product indoors 
can result in death due to 

carbon monoxide, a poison gas you cannot see or 
smell. Never operate indoors, even if windows and 
doors are open. Only use outdoors and far away 
from windows, doors and openings or vents.

4.

Manufacturer will not be liable for any changes 
made to our standard machines or any components 
not purchased from us.

5.

The best insurance against an accident is 
precaution and knowledge of the machine.

WARNING: Be extremely careful 
when using a ladder, scaffolding 
or any other relatively unstable 
location. The cleaning area should 
have adequate slopes and 
drainage to reduce the possibility 
of a fall due to slippery surfaces.

VERTISSEMENT: Faire preuve 
d'une extrême prudence au 
moment d'utiliser une échelle, des 

échafaudages ou toute autre surface relativement 
instable. La zone de nettoyage doit avoir une pente 
et un drainage adéquats pour réduire la possibilité 
d'une chute due à une surface glissante.

21. Do not allow acids, caustic or abrasive fluids to 

pass through the pump.

22. Never run pump dry or leave spray gun closed 

longer than 1-2 minutes.

23. Machines with shut-off spray gun should not be 

operated with the spray gun in the off position for 
extensive periods of time as this may cause 
damage to the pump.

24. Protect discharge hose from vehicle traffic and 

sharp objects. Inspect condition of high pressure 
hose before using or bodily injury may result.

25. Before disconnecting discharge hose from water 

outlet, turn burner off and open spray gun to allow 
water to cool below 100° before stopping the 
machine. Then open the spray gun to relieve 
pressure. Failure to properly cool down or maintain 
the heating coil may result in a steam explosion.

26. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

27. Do not operate this machine when fatigued or 

under the influence of alcohol, prescription medica-
tions, or drugs.

28. In oil burning models, use only kerosene, No.1 

home heating fuel, or diesel. If diesel is used, add a 
soot remover to every tankful.

WARNING: Do not spray machine 
or any people, animals or elec-
trical parts.

AVERTISSEMENT: Ne pas 
vaporiser sur la machine ou les 
gens, les animaux ou les pièces 
électriques

Follow the maintenance instructions 
specified in the manual. 

Suivre les instructions d'entretien 
spécifiées dans le manuel.

Karcher HDS 600-612 Operator’s Manual 9.800-080.0 - AK

WARNING

DO NOT SPRAY 

MACHINE OR ANY 

PEOPLE, ANIMALS OR 

ELECTRICAL PARTS.

WARNING

PROCTECT FROM

FREEZING

WARNING

RISK OF INJURY

FROM FALLS WHEN

USING LADDER.

DANGER

RISK OF 

ASPHYXIATION. 

USE THIS PRODUCT 

ONLY IN A WELL 

VENTILATED AREA.

Summary of Contents for HDS 3.9/30 Pe Cage

















































Reviews: