background image

     

7

1 Wear indicator
2 Vacuum lip

The vacuum lips must be replaced or re-
versed if they are worn down to the wear in-
dicator.

Remove the vacuum bar.

Unscrew the star grips.

Remove the plastic parts.

Remove the vacuum lips.

Insert new or reversed vacuum lips.

Insert the plastic parts.

Screw in and tighten the star grips.

Remove the rubber strip and clean the 
channel with a cloth. After cleaning, re-
place the rubber strip evenly.

Lift the cleaning head. 

Loosen the lock of the wiper flap.

Push the bearing lid down and remove.

Pull out the brush roller.

Note

: The brush rollers must be re-

placed when the bristle length has 
reached 10 mm.

Insert a new brush roller.

Reassemble the bearing lid in the re-
verse sequence.

Repeat process on the opposite side. 

Lift the cleaning head. 

Press the pedal for changing the brush-
es downward beyond its resistance.

Pull the disc brush out of the side below 
the cleaning head.

Hold the new disc brush under the 
cleaning head, push upward and lock.

Push the appliance forward about 2 m 
so that the steering rollers point toward 
the rear.

Press the pedal for lowering the clean-
ing head downwards slightly and then 
move it to the left. This unlocks the ped-
al. Release the pedal slowly upwards.
The lift arm of the cleaning head will be 
lowered.

1 Spring element
2 Locking pin
3 Terminal strip cover
4 Lock of safety pin
5 Excenter lever

Remove the terminal strip cover.

Place the cleaning head halfway in front 
of the appliance.

Connect the mains supply cable of the 
cleaning head to the appliance.

Attach the terminal strip cover.

Connect the hose couplers on the cleaning 
head to the hose on the appliance.

1 Push handle
2 Cleaning head

Insert the push bow into the cleaning 
head intake.

1 Safety splint

Insert the locking pins from below into 
the mount of the cleaning head.

1 Safety splint
2 Linch pin

Insert the linch pin through the locking 
pins and fold the locking rings forward.

1 Excenter lever
2 Locking pin

Open the excenter lever of the slideable 
intake on the lift arm.

Press the cleaning head all the way 
against the push handle.

Note

: The less play the cleaning head 

has after being installed, the less vibra-
tion will occur during cleaning.

Move the intake and insert the safety 
pin and lock it into place.

Close the excenter lever.

Swivel the water reservoir all the way 
down, check the lock.

The removal will take place in the opposite 
order of the installation.

CAUTION

When the cleaning head is removed, the 
stability of the appliance can be compro-
mised; ensure a safe stance.
Possibly support the rear to prevent tipping.

Replace or turn vacuum lips

Clean water distribution channel

Replacing the brush rollers

Replacing the disk brushes

Install cleaning head

Dismantling the cleaning head

20

EN

Summary of Contents for B 60

























Reviews: