-
9
If the display shows different error messag-
es or if the error cannot be remediated:
Remove the Intelligent Key.
Wait for 10 seconds.
Plug in the Intelligent Key.
If the fault recurs, call customer service.
Faults with display
Display
Remedy
ERR_I_BÜRSTE_049
Check if foreign matters block the brushes; remove foreign matter if required.
ERR_I_TURB_050
Check suction turbine for contamination and clean it if necessary.
ERR_U_BATT_001
Check battery; charge it if required.
Faults without display on the console
Fault
Remedy
Appliance cannot be
started
Stand-by. Turn the appliance off and reinsert the Intelligent Key.
Turn the program selection switch to the desired programme.
Check battery; charge it if required.
Make sure that all battery terminals are connected.
Insufficient water quan-
tity
Check fresh water level, refill tank if necessary.
Increase the water volume on the regulating knob for water volume.
Unscrew the lock of the fresh water reservoir. Remove and clean the fresh water filter. Insert the filter and screw
in the lock.
Remove the water distribution strip from the cleaning head and clean water canal (only R cleaning head).
Check hoses for blockages; clean if required.
Do not add detergents Increase the water volume to activate the dosing pump.
Check the detergent level
Insufficient vacuum per-
formance
Clean the seals between waste water tank and cover and check for tightness, replace if required.
Wastewater reservoir is full; shut off the appliance and empty the wastewater reservoir
Check protective turbine strainer for soiling, clean if necessary.
Clean the vacuum lips on the vacuum bar, replace if required
Check suction hose for blockages; clean if required.
Check the suction hose for tightness; replace if required.
Check if the cover on the dirt water discharge hose is closed
Check the setting of the vacuum bar.
Insufficient cleaning result Check the brushes for wear, replace if required.
Brushes do not turn
Check if foreign matters block the brushes; remove foreign matter if required.
If over-current switch in the electronics system has been triggered, turn programme selection switch to "OFF".
Afterwards, set it back to the desired programme.
Vibrations during cleaning You might need to use softer brushes.
Cleaning head has play, open the excenter lever and press the cleaning head all the way against the push han-
dle, close the excenter lever.
In case of faults that cannot be remedied using the table below please contact the customer service.
Accessory B 60
BR appliances B 60 W Bp (brush roller accessories)
Description
Part no.:
Working
width
550 mm
Part no.:
Working width
650 mm
Description
Packaging unit
Appliance requires
Brush roller, red (medium, standard)
6.906-934.0 6.906-935.0
Also for regular cleaning of heavily dirtied
floors.
1
2
Brush roller, white (soft)
6.906-977.0 6.906-981.0
For polishing and cleaning sensitive floors. 1
2
Brush roller, orange (high/ low)
6.906-978.0 6.906-982.0
For scrubbing structured floors (safety
tiles, etc.).
1
2
Brush roller, green (hard)
6.906-979.0 6.906-983.0
For thoroughly cleaning heavily dirtied
floors and for removing the coating (for
e.g. of wax, acrylate).
1
2
Brush roller, black (very hard)
6.906-980.0 6.906-984.0
1
2
Pad roller shaft
4.762-432.0 4.762-433.0
For intake of roller pads.
1
2
Roller pad, yellow (soft)
6.369-454.0 6.369-454.0
For polishing floors.
20 80
96
Roller pad, red (medium)
6.369-456.0 6.369-456.0
For cleaning slightly dirtied floors.
20 80
96
Roller pad, green (hard)
6.369-455.0 6.369-455.0
For cleaning normal to heavily dirtied
floors.
20 80
96
22
EN
