Kanuk GmbH • Hauptstraße 131 • 01744 Dippoldiswalde
139
EN
KanUK DesIGn
�tr�ct�re
XV
82,7 cm
75,5 cm
29 cm
38,7 cm
90,4 cm
1
7
8
2
4
5
3
48 cm
12,5 cm
100 mm
15 cm
14,9 cm
Kanuk Design LuTo ceramic insert
tipp:
Wear gloves to protect against contamination and for a better grip of the smoke deflector plates.
these instructions apply only to the luto Xv. In the luto vIII only one baffle plate is mounted. to insert the
smoke baffle, be sure to get a second person to help you.
To insert the smoke baffle, first remove the round steel plate on
the top of the stove..
The front smoke baffle plate is already inserted in the
dome of the firebox. Person 1 lifts this up through
the opening in the top of the fireplace so that person
2 in the combustion chamber can carefully remove
the upper left or right firebox stone with both hands.
Now person 2 places the closed smoke baffle in the
firebox, lifts it with both hands and pushes it to the
end of the firebox.
Person 1 now takes over the rear ceramic plate
in addition to the front one and holds both
smoke baffle plates from above through the
round opening, while person 2 puts the side
stone back in place. Make sure that the spa-
cers are evenly distributed on the ceramic and
then release the smoke baffle plates. Make
sure that all ceramic parts (base, sides, baffle
plate) are pushed back against the rear wall.
Kanuk Design LuTo side panel mount
step I - Fastening the two brackets to the front panel
To install the mounting brackets, you need to disassemble the Allen screws (A). To do this, you will need a size 19
ring or open-end wrench to lock the cap nuts (B) and a size 10 Allen wrench to remove the hexagon socket screws.
Now put the angles included with the side panel onto the hexagon socket screws (A) and tighten them hand-tight.
step II - Fastening the angle bracket to the rear panel
First, using a size 13 box wrench or open-end wrench, loosen all six cap nuts (C) on the heat shield plate on the back
of the furnace. Pull the heat shield plate off the screws and set it aside. Now remove the center extension nuts (D)
and attach to the body (E) the brackets for the side plate. Hand tighten the extension nut only to be able to align the
side plate.
step III - stop the side plate and align the angles, final assembly
Hold the side plate against the stove and align the angle to the holes. Now retighten the hexagon socket screws and
the cap nuts on the back. The side plates and the heat protection plate can then be attached to the angles.
Summary of Contents for Bank
