manualshive.com logo in svg

Kanmor Zone Control 369e, Manual

Share
Download
Kanmor Zone Control 369e Manual Download Page 21

 

21 of 32 

© 2003 

D 369e - 06/03

Monitor 

Menu (2 of 2)

Note:

 

To clear the recorded information in the specifi c item fi eld, press and hold 

▲

 and 

▼

.

0 to 9999 hr

0 - 255

0 - 255

LTD

INST ADV

USER

Item Field

Description

Access
Level

Range

The number of times that the microprocessor in the control 
has reset since this item was last cleared. The control will 
reset itself if it has experienced some form of interference 
that has disrupted its operation. This can be used to give an 
indication of the quality of the electrical environment that the 
control has been installed in.

The number of times that the control has been powered up 
since this item was last cleared. This number will increase if 
there is a lowering of the input voltage beyond the control's 
usable range. This item can also be used as an indication of 
the quality of the power source.

The total number of 

Zn 6

 relay running hours since this item 

was last cleared.

:00 to :59

Default = :00

12: AM to 11: PM or
00: to 23:

Default = 12: AM

12 hr, 24 hr

Default = 12 hr

SATURDAY, . . . ,
FRIDAY

Default = SATURDAY

 Section

LTD

INST ADV

USER

C

C

C

C

C

Item Field

Description

Access
Level

Range

Displays current time of day and the day of week

DIP switch = 

Setback

Real time clock minutes

DIP switch = 

Setback

Real time clock hours

DIP switch = 

Setback

Day of the week

DIP switch = 

Setback

Method of displaying time on the control's display

DIP switch = 

Setback

AM

AM

Time 

Menu (1 of 1)

Summary of Contents for Zone Control 369e

































Reviews:

No comments

Brands by name

Popular brands

Load more brands