manualshive.com logo in svg

Kanmor Zone Control 369e, Manual

Share
Download
Kanmor Zone Control 369e Manual Download Page 12

 

12 of 32 

© 2003 

D 369e - 06/03

Installation

Press down at the fingertip 
grips on top of the front cover 
and pull out and down.

Lift the front cover up and 
away from the control.

Loosen the screws at the 
front of the wiring cover.

The wiring cover pulls 
straight out from the 
wiring chamber.

Remove the safety dividers 
from the wiring chamber by 
pulling them straight  out  of 
their grooves.

Press the control release 
clip on the base inside the 
wiring chamber and slide 
the control upwards.

The control lifts up and away 
from the base.

The base is ready for 
mounting. There are 10 
conduit knock-outs at 
the back and bottom of 
the wiring chamber.

Release Clip

13 mounting holes

The control can be mounted 
on a standard DIN rail. This 
will be a popular option for 
those who prefer to mount 
the control inside a larger 
electrical panel.

The wiring can enter the bottom 
or the back of the enclosure. 
Knock-outs provided in the base 
allow the wiring to be run in con-
duit up to the enclosure. The 
base also has holes that line up 
with the mounting holes of most 
common electrical boxes.

CAUTION 

Improper installation and operation of this control could result in damage to the equipment and possibly even personal injury. 
It is your responsibility to ensure that this control is safely installed according to all applicable codes and standards. This 
electronic control is not intended for use as a primary limit control. Other controls that are intended and certified as safety 
limits must be placed into the control circuit. Do not open control. Refer to qualified personnel for servicing. Opening voids 
warranty and could result in damage to the equipment and possibly even personal injury.

STEP ONE 

 GETTING READY 

Check the contents of this package. If any of the contents listed are missing or damaged, please contact your wholesaler or 
kanmor sales representative for assistance.

Type 369e includes:

   One Zone Control 369e, One Outdoor Sensor 070e, Data Brochures D 369e, D 070e, 

 

 

User Brochure U 369e.

Note:

 Carefully read the details of the Sequence of Operation to ensure that you have chosen the proper control for your application.

STEP TWO 

  MOUNTING THE BASE 

Summary of Contents for Zone Control 369e

































Reviews:

No comments

Brands by name

Popular brands

Load more brands