background image

Copyright

 © 

Kanda 2013

17

Further Information

More information about AVR code and programming can be found online

 

www.avrfreaks.com

 – a forum and help site for AVR

 

www.kanda.com/support

 – new software versions, FAQ and documents about AVR and

kanda tools

 

www.atmel.com/products/avr

   - more information about AVR microcontrollers

  Books are available at Amazon. Kanda supply a basic book at

      

www.kanda.com/go/KB0010

Other tools and accessories

We supply add-ons for the STK300, including LCD modules, keypads, Flash RAM, 24C
EEPROMs, extra mounted Atmega128 devices, ICE  and a universal power supply.

  Flash RAM and Address Latch – see  

www.kanda.com/go/STK200-RAM

  LCD module – see 

www.kanda.com/go/570910-PM

  Data Entry Keypad – see 

www.kanda.com/go/780305-PM

  JTAGAVR ICE – see 

www.kanda.com/go/JTAGAVR

  Power supply – see 

www.kanda.com/go/PSU9V-UNI

  Mounted Atmega128 device – 

www.kanda.com/go/KANMEGDEV5

  Mounted Atmega128L device – 

www.kanda.com/go/KANMEGDEV3

  24C Serial EEPROM – see 

www.kanda.com/go/EE-02

Copyright

Atmel, AVR Studio and AVR are Registered Trade Marks of Atmel Corp., San Jose,
California, USA

Summary of Contents for STK300



















Reviews: