K-TRON K-Vision Programming Instructions Manual Download

Page: 34 / 121

Programming Reference

1.7 Machine setup menu

Page 34

Docu-No.: 0590020601-EN Rev. 1.6.0

1.7

Machine setup menu

This menu programs the feeder specific information. The data is
arranged in three separate screens or menus.

1.7.1

General sub-menu

Parameter

Definition

SETPOINT MODE

Setpoint Mode

Setting

Meaning

LOCAL

Feeder is operated as an individual unit.

RATIO

Percentage of an external analog setpoint input =
operating setpoint.

DIRECT

External analog setpoint input = operating setpoint.

LINE1-8

Feeder Setpoint is entered from the Line overview
Page. In this mode the feeder is assigned to a line.
It's called recipe mode. Use Line1 for KSL.

Input range: See list Default Local

MAX SETPT

Maximum Setpoint

Input of a maximum permissible setpoint value.

This value depends on the maximum throughput performance of the
feeder.

Note:

This value also scales the ratio setpoint input and massfow

and setpoint analog outputs.

Input range: 0 to 999999 kg/h Default: 7200 kg/hr.

UNITS

Units Selection

Selection of the desired units.

Note:

This selection change automatically all weight specific units.

Setup:

kg/h, kg/min, lb/h, lb/min, T/h (metr. Ton), ET/h (engl. Ton), gr/h, gr/
min.

Input range: See list Default kg/h

RUN TIME-[hours]

Feeder Run Time

Display of the total run time in hours. A value may be entered as a
baseline.

Input range: Normal Display only

FDR ADDR

Feeder Number or

Feeder Address

Address of the selected KCM.

Note:

• If the KCM CPU DIP switch, positions <1> to <5> are all set to <0>,

then the feeder address is set by this entry, else it is from the DIP
switch and then this parameter is ‘read only’.

Table page 1 of 2

Summary of Contents for K-Vision


























































































































Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands

K-TRON K-Vision, Programming Instructions Manual

Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands