K-TRON K-Vision Programming Instructions Manual Download

Page: 110 / 121

Appendix

5.8 LWF ASR Map

Page 110

Docu-No.: 0590020601-EN Rev. 1.6.0

45 DRIVE CMD
CEILING

• Drive command has reached the

limit <DC CEILING>

46 DRIVE CMD
HIGH

• The drive command has exceed the

value <DRV CMD HI> Limit in the
<ALARM> menu.

47 DRIVE CMD
LOW

• The drive command has dropped

below the value <DRV CMD LO>
Limit in the <ALARM> menu.

48
CHECK_MOTOR_B
RUSHES

• DC motor brushes may be wearing

out and ready to fail.

49
RESET_WHILE_RU
N

• It is set if the feeder was running

before the power down or reset
occurred

50 ACF_FAIL

• Actiflow has an alarm

52 FEEDFACT. BAD

• Feedfactor is zero or feeding

condition changed so that the
feedfactor exceed the set limit in the
<ALARM> menu <FF DEV LIMIT>.

53
SCALE
OVERRANGE

• The weight on the scale is above the

scale gross range permitted.

54
SCALE
UNDERRANGE

• The weight on the scale is below the

zero or gross weight < 0.

ASR(

Alarm number)

Description

Table page 5 of 6

Summary of Contents for K-Vision


























































































































Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands

K-TRON K-Vision, Programming Instructions Manual

Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands