K-TRON K-Vision Programming Instructions Manual Download

Page: 71 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 71

Alarm Messages- Cause and Remedy

System alarms 4.1

14
MOTOR
OVERLOAD

• Motor current limit is exceeded.

Note:

The Safety switch is not designed to be
used as a normal way of interlocking
the KCM. It is used for safety control
only.



Reduce motor load.



Check motor power limit in the
<MECHANICAL> menu,
<MOTOR> sub-menu.



Review material/feeder selection.

15
MDU SAFETY
RELAY

• Safety relay failed to close contacts

on power up and contacts remained
closed after power down.



Replace Drive pcb.

16
MOTOR/ENCDR
FAIL

• Dual tach signals connected, one

failed.

• Over-voltage on drive power supply.

• Motor voltage applied but no speed

feedback.

• Drive temperature > 85 deg. C.



Check tachometer-replace.



Check motor brushes.



Replace motor if required.



Replace KCM drive board.



Check for excessive line voltage.



Reduce operating temperature.

17
MDU
UNCONTROLLED

• Speed feedback but no motor

voltage applied.



Replace drive board.

18
MDU EEPROM
FAILED

• EEPROM checksum failed.



Cycle power. If error persists,
replace drive pcb.

19 MDU DRIVE
FAILED

• MDU drive pcb has failed. (vibratory

drive only. Drive coil current too
high)



Exchange vibratory drive pcb.



Check drive coil for proper
impedance.

20 MDU POLARITY

• Coil polarity is incorrect on the

vibratory drive. (Vibratory feeder
only)

• Displacement frequency out of

range.



Change the feedback coil polarity
by swapping leads at KCM.

21 HCU REMOVED

• HCU was removed.



Connect HCU at the KCM and
switch KCM On.



Repoll SFT channel to re-connect
HCU.



Clear NOVRAM if necessary.

22 HCU ALARM

• HCU has an alarm.



See following alarms for trouble
shooting.

Alarm Num- Alarm

Cause

Remedy

Table page 3 of 7

Summary of Contents for K-Vision


























































































































Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands

K-TRON K-Vision, Programming Instructions Manual

Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands