K-TRON K-Vision Programming Instructions Manual Download

Page: 12 / 121

Programming Reference

1.1 Product change menu

Page 12

Docu-No.: 0590020601-EN Rev. 1.6.0

GEARSWITCH

Note:

Not used for vibratory feeders

Defines how the unit will change gear reductions on the K2 feeder
with motor reversing gear reduction switching. To activate, a digital
output must be set to <HILoGear>. Selections are:

High, Low, Auto Hi, Auto Lo

Notes:

• See more detail of operation section

5.1.1.

• To fix the reduction at either High or Low speed, select either High

or Low entries.

• This value is only displayed when internal KCM motor drives are

used.

• <Low> selects low speed/highest gear reduction.

• <High> selects high speed/lowest gear reduction.

• <Auto Hi> When entering a setpoint which will generate a drive

command of more than 50% and the GEARSWITCH is on Auto
Lo, the gear will switch to high and the GEARSWITCH parameter
changes to Auto Hi.

• <Auto Lo> When entering a setpoint which will generate a drive

command of less than 10% and the GEARSWITCH is on Auto Hi,
the gear will switch to low and the GEARSWITCH parameter
changes to Auto Lo.

AUTO TARE

This command allows the current weight value to be entered into the
TARE memory when the product hopper is empty.

Switch of the automatic refill and then tare.



For KSU-II/KCM select parameter then press



For KSL press

F5-MORE

then



For KSC press

TARE

Tare Weight

Weight of the feeder and hopper with no material. This value will set
automatically when Auto Tare function is executed.

Input range: 0 to scale range [kg]

NET WEIGHT

Net Weight

Display of the current weight of the feeding material on the scale.

Net weight = Gross Weight - Tare

Range: Display only 0 to scale range [kg]

Parameter

Definition

Table page 2 of 5

Summary of Contents for K-Vision


























































































































Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands

K-TRON K-Vision, Programming Instructions Manual

Search results

Summary of Contents for K-Vision

Reviews:

Related manuals for K-Vision

Brands by name

Popular brands