JVC VN-V686WPU Instructions Manual Download

Page: 5 / 121

Safety Precautions ........................................ 2

Contents........................................................ 5
Features ........................................................ 6

Safety precautions......................................... 7

Operating Environment ................................. 8
Precautions ................................................... 8

Name and Function of Parts ....................... 12

Features ...................................................... 14
Camera Mounting Procedures .................... 15

Connection/Installation

Mounting the Camera.................................. 16

Power Connection ....................................... 20
LAN Cable Connection................................ 22

Connecting the alarm signal cable .............. 22

Network Requirements................................ 24

Network Settings

IP Address Settings..................................... 26

Setting the IP address for VN-V686WPU ... 26

When the IP address of

VN-V686WPU is known....................... 31

When the IP address of

VN-V686WPU is unknown.................. 31

Setting Using Internet Explorer

Preparation.................................................. 32

Internet Explorer Setup ........................... 32

Enter user name and password............... 34

Setting ......................................................... 36

View Page ............................................... 36

Camera Page .......................................... 38
Encoding Page ........................................ 44

Alarm Page.............................................. 46

Alarm Environment Page......................... 50
PTZ Page ................................................ 54

Auto Patrol Page...................................... 60

Privacy Mask Page.................................. 62
Motion Detection Page ............................ 64

Basic Page .............................................. 66

Details Page ............................................ 68

Protocol Page .......................................... 69

Streaming Page....................................... 70
Access Restrictions Page........................ 72

Time Page ............................................... 74

Password Page........................................ 75

Maintenance Page .................................. 76
List of Factory Settings of Each Page ..... 78

Miscellaneous page................................. 82

Operation Page ....................................... 83
Settings Page .......................................... 84

Position List Page .................................... 87

Patrol Settings Page................................ 89

Settings and operation of Built-in
Viewer

Built-in Viewer ............................................. 91
Preparation.................................................. 92

JPEG Viewer............................................... 95

MPEG4 Viewer.......................................... 100
Shortcut for Built-in Viewer........................ 105

PTZ Controller Operation .......................... 106

Operation............................................... 106
Intelligent Tracking (Manual Mode) ....... 111

Registering Preset Positions ................. 112

Auto Pan Setting.................................... 113
Auto Trace Setting ................................. 115

Others

Troubleshooting ......................................... 116

Specifications ............................................ 119

Contents

This manual contains the detailed
instructions for using the

VN-V686WPU

camera.
Please refer to

[START-UP GUIDE] for

description on the general usage of

VN-

V686WPU.
For the latest information, please refer to the

Readme

file in the CD-ROM supplied with

this product.

●

The supplied CD-ROM includes
[INSTRUCTIONS] (this manual) (pdf), [API
Guide] (pdf), [VSIP Guide] (pdf) and [Search
tool].

Summary of Contents for VN-V686WPU


























































































































Search results

Summary of Contents for VN-V686WPU

Reviews:

Related manuals for VN-V686WPU

Brands by name

Popular brands

JVC VN-V686WPU, Instructions Manual

Search results

Summary of Contents for VN-V686WPU

Reviews:

Related manuals for VN-V686WPU

Brands by name

Popular brands