JVC VN-V686WPU Instructions Manual Download | Manualshive

Page: 116 / 121

background image

116

Others

Troubleshooting

Symptom

Causes and Countermeasures

Reference

Page

Video image does not appear
Power does not turn on.

●

Is there a problem with the power cable connecting
this unit and the power unit? (If the power cable is
too long or thin, the cable resistance will be high
and the correct voltage may not be supplied.)

B

Use a cable of low resistance and the correct

cable length. (When the camera is operating
(at rated current), check that the supplied
voltage is of the rated voltage at the terminal
of the camera.)

●

Is the lens cap attached?

B

Remove the lens cap.

IP address of VN-V686WPU
is unknown

●

The default IP address is 192.168.0.2, and the
default subnet mask is 255.255.255.0.

●

When [IP Setting] is set to

A

DHCP

B

, this product

will run using the default IP address when it is
started up via a LAN in which a DHCP server does
not exist.

●

Search tool in attached CD-ROM is available to find
VN-V686WPU from a PC in the same LAN.

The web page of VN-
V686WPU cannot be
displayed

Check the Internet Explorer settings.
When a proxy server is in use, configure the proxy
server settings of the Internet Explorer accordingly.

Built-in Viewer cannot be
installed

Check the Internet Explorer settings.
Built-in Viewer consists of a software component
called ActiveX.
The ActiveX is usually installed when Built-in Viewer
is used for the first time. However, installation may
be rejected depending on the Anti-virus software
settings. In this case, change the settings of the
Anti-virus software before installing Built-in Viewer.

Authentication by Verisign
appears during installation of
Built-in Viewer

Verisign’s electronic signature is stored in Built-in
Viewer.
For computers with a network environment that is
connected to the Internet, the authenticity of the
Viewer can be verified via authentication by
Verisign.

^

«
...
114
115
116
117
118
...
»

Summary of Contents for VN-V686WPU


























































































































Reviews:

No comments

Related manuals for VN-V686WPU

EF35mm f/1.4L II USM

Brand: Canon Pages: 2

EF LENS TS-E24MM F/3.5L

Brand: Canon Pages: 19

Brand: Canon Pages: 14

Brand: EasyN Pages: 11

Brand: UEi Pages: 6

Brand: MagicRadar Pages: 98

Brand: Mami Pages: 16

Brand: NA-DE Pages: 8

Brand: Abus Pages: 16

Brand: D-Link Pages: 2

DCS-1130 - mydlink-enabled Wireless N Network...

Brand: D-Link Pages: 58

Brand: Canon Pages: 43

Brand: unii Pages: 2

Brand: Silent Witness Pages: 26

Brand: DELTA PLUS Pages: 80

Brand: Observint Pages: 23

Brand: E-Vision Pages: 20

Brand: Idis Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands