manualshive.com logo in svg

JVC VN-V686WPU, Instructions Manual, Page: 22 / 121

Share
Download
JVC VN-V686WPU Instructions Manual Download Page 22

22

Connection/Installation

Connect the camera to a hub or computer using 
a LAN cable.

䢇

When connecting to a hub

Make use of a straight cable.

䢇

When connecting to a computer

Make use of a cross cable.

Note

：

                                                       

●

However, cross cables cannot be used with 
some computer models. When connecting VN-
V686WPU directly to a computer, check the 
computer’s LAN specifications in advance.

Connect the alarm signal cable to external 
devices, such as a sensor or buzzer.

Note

：

                                                       

●

Noises from an external source may cause the 
camera to malfunction even when the cable 
used is within 50 m. In this case, move the cable 
away from the noise source.

LAN Cable Connection

Cable to use

●

Shield (STP) cable

●

Make use of a Category 5 (or higher) cable 
when 100BASE-TX is used.

RJ-45 
conversion 
connector 
(provided)

Connecting the alarm signal 
cable

Cable to use

●

Length of 50 m or shorter

●

UL1007, UL1015 or equivalent products

●

AWG#22 to AWG#18 or equivalent products

Solder welding or 
crimping

Insulating 
tape

Summary of Contents for VN-V686WPU


























































































































Reviews:

No comments