JVC VN-V686WPU Instructions Manual Download

Page: 12 / 121

Getting Started

Camera

Camera securing hole (4 locations)

This hole is used for mounting the camera on the wall.

Cable connecting hole, cap

Remove the cap and pull out the cables from this
hole for connection.
(

Page 17)

Fall Prevention Wire

Connects the camera to the wall. Secure the
camera tightly to the anchor bolts used to mount
the fall prevention wire on the wall. (

Page 18)

AC24V Power Cable

Connects the camera to AC24V power. (

Page 20)

Alarm Input/Alarm Output Cable (x8)

This cable is for alarm input and alarm output.
(

Page 22)

LAN Cable

This connects the unit to the network.
(

Page 22)

Dome Cover

The dome cover is a delicate object. Handle it
with care.

Note

：

●

It is covered with a protective sheet during
shipment. Do not remove this sheet until
installation is complete.

Dome Cover Fixing Screws (x4)

Name and Function of Parts

䡵

Front side

Cable color

Signal Name

Brown

Input 1

Red

Input 1 (COM)

Orange

Input 2

Yellow

Input 2 (COM)

Green

Output 1

Blue

Output 1 (COM)

Purple

Output 2

Gray

Output 2 (COM)

Summary of Contents for VN-V686WPU


























































































































Search results

Summary of Contents for VN-V686WPU

Reviews:

Related manuals for VN-V686WPU

Brands by name

Popular brands

JVC VN-V686WPU, Instructions Manual

Search results

Summary of Contents for VN-V686WPU

Reviews:

Related manuals for VN-V686WPU

Brands by name

Popular brands