JVC TK-C553E Service Manual Download Page 46

Page: 46 / 58

Mount the camera body.
1) Ensure that the camera clamping

screw on the ceiling mount is
loosened.

2) Align the camera position alignment

mark on the camera body with the
camera position alignment mark on
the ceiling mount and press the
camera body straight against the
mount.

Note

Exercise caution when mounting so as not
to pinch the drop prevention wire and the
connected cables.

3) Rotate the camera body clockwise as

far as it will go.
At this point, check that the camera
body clamp is located on the lock
screw on the ceiling mount.

4) Tighten the camera clamping screw.

CAUTION

Be sure to tighten the camera clamping
screw fully. Otherwise the camera body
may vibrate or drop from the ceiling.

To dismount the camera from the ceiling,
perform steps

in reverse order.

Rotate the
camera body
clockwise

Camera clamping
screw

Camera
clamping screw

Tighten the camera
clamping screw.

(1)

(2)

(3)

(2) Position alignment mark

(2) Camera position
alignment mark

Clamp

(4)

Ceiling Installation (Continued)

INSTALLATION

Adjusting the Camera Angle

Remove the dome cover.
Rotate the dome cover counterclockwise and
pull it off.

Horizontal rotation
(adjustable range: 90°)
1.

Loosen the horizontal LOCK screw.

Holding the both tilt lock screws, rotate
horizontally.

Tighten the horizontal LOCK screw.

Vertical rotation
(adjustable range: 130°)
1.

Loosen the tilt lock screws.

Holding the rotation levers, rotate
vertically.

Tighten the tilt lock screws.

Image inclination
(adjustable range: 30°)

Manipulate the rotation levers to adjust the
inclination of the image.

Adjusting the image size

Adjust the size using the zoom ring.

Adjusting the focus

Adjust using the focus ring.
When required, the surveillance image
should be adjusted, etc. This adjustment
is performed using the setup screen.

MONITOR

LOCK

LEFT

RIGHT

SET

AWC

DOWN

NOT USED
NOT USED
L/L
ON

INT
OFF

TERMINATION

Horizontal LOCK
screw

Dome
cover

Camera head

Rotation levers

Tilt lock screws

Focus ring

Zoom ring

Summary of Contents for TK-C553E


























































Search results

Summary of Contents for TK-C553E

Reviews:

Related manuals for TK-C553E

Brands by name

Popular brands

JVC TK-C553E, Service Manual

Search results

Summary of Contents for TK-C553E

Reviews:

Related manuals for TK-C553E

Brands by name

Popular brands