14
Settings
CAMERA FACE
• Video synchronization selector switch
(INT/LL)
Set to LL (Line Lock) on all cameras, and
align V.PHASE.
(
See page 29.)
• Control signal termination ON/OFF switch
(TERMINATION OFF/ON)
Set this to ON only on the camera placed
at the end of the control signal cable.
Set to OFF on all other cameras.
Menu Screen Settings
COMMUNICATION menu screen
• MODE item: Set to DUPLEX
• STYLE item: Set to MULTIDROP
• ID item: Set the camera ID.
For each camera, match the ID with the
VIDEO INPUT number of the RM-
P2580.
* Settings on the COMMUNICATION
menu screen are performed using the
operation buttons on the front section
of the camera.
MEMO
Following selection of MEMORY, the settings
on the COMMUNICATION menu will not be
valid before the power has been turned on
again.
FUNCTION menu screen
Screen for making settings related to the
Auto Patrol and Auto Pan functions and
display of text.
The number shown in
the
M M
part of ID-
MM
should be correct.
NOT USED
NOT USED
MONITOR
LOCK
LEFT
RIGHT
SET
UP
DOWN
ON
LL
OFF
TERMINATION
INT
L/L
ON
INT
OFF
TERMINATION
AWC
P R O T
O
O
L : D U P L E X
I D - 0 5
C
MONITOR screen
“DUPLEX” should be
displayed.
• Settings on the FUNCTION menu are
performed using the operation buttons
on the RM-P2580. They cannot be
made using the operation buttons on
the camera body.
• Make settings on other menus as
required.
Monitor screen (example showing camera ID as “05”)
SYSTEM
System with Remote Control Unit RM-P2580
MEMO
When operating a system using the RM-
P2580, several cameras (up to 16) can be
connected and used on one control signal
cable. Consequently, an incorrect switch
setting on just a single camera will cause
the entire system to work incorrectly.
• Confirm switch settings on the screen
as follows.
q
Confirm that the image from the camera
to be checked is displayed on the monitor.
w
Turn OFF and then ON the power to the
camera to be checked.
e
When the STYLE item is MULTIDROP,
characters similar to those shown in the
figure below are displayed for about 5
seconds. They do not appear in the case
of POINT to POINT.
r
Confirm that “DUPLEX” and “ID-
MM
” are
displayed and that the ID number is the
correct number (the number should be the
same as the number of the VIDEO INPUT
terminal to which the camera is connected
on the rear panel of the RM-P2580).
t
If wrong, set the MODE item, STYLE item
and camera ID again.
15
Connections to Camera Terminal Board
INSTALLATION
Connections to Terminal Board
Remove the terminal board cover and con-
nect the video signal cable (coaxial cable)
(
×
1).
Connect the DC 12 V or AC 24 V power cables
(
×
2).
In a system where the Remote Control Unit
(RM-P2580), etc. is used, connect the con-
trol signal cables (
×
4).
DC 12 V or AC 24 V power supply cable
Connect the DC 12 V or the AC 24 V power
supply to the DC 12V/AC 24V terminals on
the terminal board. To prevent connection
errors or a cable disconnection, we recom-
mend the use of lug plates for the connec-
tions.
The following table shows the connection dis-
tances and connection cables provided that
2-conductor VVF cables (vinyl-insulated vi-
nyl sheath cables) are used.
Maximum extension
(reference)
Conductor
diameter
100 m
260 m
410 m
500 m
1.0
∅
mm 1.6
∅
mm 2.0
∅
mm 2.6
∅
mm
and more and more and more and more
Remove the terminal board
cover by flipping it up while
pushing its top to the left.
RX+ C
RX– D
A TX+
B TX–
Terminal board
Lug plates
DC 12 V or AC 24 V
power cable
To DC 12 V or AC
24 V power supply
Control signal cable
To Remote Control
Unit (RM-P2580)
To Remote Control Unit
(RM-P2580)
Video
signal cable
• Do not allow input from both a DC 12 V
and AC 24 V power supply at the same
time.
• When using a DC 12 V power supply,
ensure that the polarities of the cable are
correct.
• The AC 24 V power supply should con-
form to the following:
U-type: Class 2 only
E-type: Isolated power supply only
• Turn OFF the power supply to all components before making connections.
CAUTION:
• If thin cables are used (i.e. with a high
resistance), a significant voltage drop
will occur when the unit is at its
maximum power consumption. Either
use a thick cable to restrict the voltage
drop at the camera side to below 10%,
or place the power supply near to the
camera. If voltage drop occurs during
operation, the performance will be
unstable.
• Attach the cable conductors so that they
do not come into contact with the drop
prevention wires.
Summary of Contents for TK-C553E
Page 30: ......
