Masterpage:Right+
EN
83
Filename [SR-MV30U_10Subsidiary.fm]
Page 83
March 30, 2004 5:46 pm
TROUBLESHOOTING
Timer Recording (DVD Deck)
●
Date and time is not correct.
]
Set date and time correctly. (
墌
pg. 20)
●
The timer is not engaged.
]
Press
DVD TIMER
(
#
) and confirm that the DVD timer lamp
lights up on the unit.
●
Timer recording is in progress.
]
Timer programing can’t be performed while a timer recording is
in progress. Wait until it finishes.
●
Date and time is not correct.
]
Set date and time correctly. (
墌
pg. 20)
●
The timer is not engaged.
]
Press
DVD TIMER
(
#
) and confirm that the DVD timer lamp
lights up on the unit.
●
There is a power outage while the DVD deck is in the timer
standby mode.
]
The unit does not enter timer standby mode automatically when
the power is restored to the unit. Engage the timer standby
mode again.
●
Date and time set on the unit is not correct.
]
Set date and time correctly. (
墌
pg. 20)
●
The channel position does not correspond to that in the
receiving area.
]
Set the correct channel position for the receiving broadcast.
(
墌
pg. 21)
●
Power failure occurred.
]
Set date and time correctly. (
墌
pg. 20)
●
Eight programs have already been timer programed.
]
Clear unnecessary programs on the unit, then try timer
programing again. (
墌
pg. 45)
●
The PC’s data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]
Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (
墌
pg. 11, 78)
Timer Recording (VCR Deck)
●
Date and time is not correct.
]
Set date and time correctly. (
墌
pg. 20)
●
The timer is not engaged.
]
Press
VCR TIMER
(
#
) and confirm that the VCR timer lamp
lights up on the unit.
●
Timer recording is in progress.
]
Timer programing can’t be performed while a timer recording is
in progress. Wait until it finishes.
●
Date and time is not correct.
]
Set date and time correctly. (
墌
pg. 20)
●
The timer is not engaged.
]
Press
VCR TIMER
(
#
) and confirm that the VCR timer lamp
lights up on the unit.
●
The timer is engaged but there’s no cassette loaded.
]
Load a cassette with the record safety tab intact.
●
The loaded cassette has had its record safety tab removed.
]
Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
●
The end of the tape was reached during timer recording.
]
The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
●
The end of the tape was reached during Instant Timer
Recording.
]
The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
●
Date and time set on the unit is not correct.
]
Set date and time correctly. (
墌
pg. 20)
●
The channel position does not correspond to that in the
receiving area.
]
Set the correct channel position for the receiving broadcast.
(
墌
pg. 21)
●
The unit’s channel positions have been set incorrectly.
]
Refer to “Changing VCR Plus+
®
Setting” (
墌
pg. 77) and re-
perform the procedure.
Timer programing cannot be made.
Timer programing recording does not start.
VCR Plus+ Timer Programing cannot be made.
On the front display panel, “– –:– –” appears.
“PROGRAM FULL” appears on the TV screen during timer
programing.
The disc space does not increase when recorded programs are
cleared.
Timer programing cannot be made.
Timer programing recording does not start.
The VCR Timer lamp on the unit won’t stop blinking.
The tape is automatically ejected, then the unit is shut off.
VCR Plus+ Timer Programing cannot be made.
The VCR Plus+ system does not timer-record properly.
SR-MV30U_00.book Page 83 Tuesday, March 30, 2004 5:46 PM
