E-20
A MODE
T
erminal Name
AUT
O
I/O 1 to 8
(I/O 9/ to 16/8)
UNIT ALARM
CAMERA SW
Condition
—
When 8 SEL OUT is set
•
I/O 1 to 8 correspond to
cameras 1 to 8.
When 8 ALM OUT is set
•
I/O 1 to 8 corresponds to
cameras 1 to 8.
—
—
Signals
The MAKE signal is output for between 500 ms and 1000 ms duration
in the following cases.
●
Power OFF
➝
ON.
●
AUT
O SEQUENCE (AUT
O button OFF
→
ON)
●
When an
AUT
O SEQUENCE operation which has been interrupted
by an alarm input resumes.
The MAKE signal is output for between 500 ms and 1000 ms duration
from the terminal corresponding to the camera number in the follow-
ing cases.
●
When
AUT
O SEQUENCE is turned OFF
, the MAKE signal is output
to the Camera No. terminal corresponding to the camera displayed
on the camera indication.
●
With
AUT
O SEQUENCE set to OFF
, each time when the camera is
selected, the MAKE signal is output to the Camera No. terminal
corresponding to the camera selected.
●
If an
Alarm is input when
AUT
O SEQUENCE is activated, the MAKE
signal is output to the Camera No. terminal corresponding to the
camera to which the
Alarm signal is input.
●
If the PRIORITY
item is set to
ALARM, when there is an
Alarm input
while
AUT
O SEQUENCE is OFF
, the MAKE signal is output to the
Camera No. terminal corresponding to the camera to which the
Alarm
signal is input.
The MAKE signal is output for between 500 ms and 1000 ms duration
in the following cases.
●
The main signal is output at the terminal corresponding to the number
of the camera which sent the alarm signal.
The MAKE signal is output continuously throughout the alarm period.
The MONIT
OR OUTPUT
2 signal will be as follows, depending on the
setting of the "CAM SWITCH".
OFF
:
Same video signal as MONIT
OR OUTPUT
1, regardless of
the CAMERA
SW terminal.
LO
W
:
The camera’
s video signal is switched at the next VD after the
falling signal from the time-lapse VCR is received.
HIGH
:
The camera video is switched at the next VD after the raising
signal from the time-lapse VCR is received.
4. CONNECTIONS
●
The master monitor displays the video signal from the selected camera.
●
Use the CAMERA
SW input to switch the video signal and record it on the VCR.
●
The preset operation, manual operation,
AUT
O P
AN operation and
AUT
O P
A
TROL
operation are available for each camera.
●
When fixed cameras are used, only the video signal can be switched.
●
The alarm operation is available using the DA
TA
I/O terminals.
●
Alarms with up to 100 positions per camera can be handled via the SERIAL-1 connector
.
In the
A
mode, in which the camera signals are input directly to the VIDEO INPUT
connectors on the rear panel, the DA
TA
I/O
terminals outputs as shown in the following table :
E-21
V
.IN
V
.IN
34
2
1
V.
OUT
VIDEO
IN
V.
OUT
VCR
OUTPUT
MASTER MONITOR
MONITOR
TIMELAPSE VCR
CAMERA 1
CAMERA 2
CAMERA 3
ID:1
ID:2
ID:3
5
6
7
8
1
TO CAMERATO CAMERA
DATA I / O
RXRX
+
RXRX
-
TXTX
+
TXTX
-
COMCOM
1
2
3
4
5
6
7
8
COMCOM
9/19/1
10/210/2
11/311/3
12/412/4
13/513/5
14/614/6
15/715/7
16/816/8
COMCOM
COMCOM
COMCOM
CAMERACAMERA
SWSW
UNITUNIT ALARMALARM
AUTOAUTO
4
3
1
2
8
7
5
6
2
3
4
5
6
7
8
1
MONITORMONITOR OUTPUTOUTPUT
MONITORMONITOR
SERIAL-2SERIAL-2
SERIAL-1SERIAL-1
VIDEO INPUT
VIDEO OUTPUTVIDEO OUTPUT
OUTPUTOUTPUT
2
1
ONON
2
3
4
5
6
7
8
POWER
OFF
ON
AC INPUT
`
REC
REC
STOP
REC
CHECK
EJECT
OPERATE
OPERATE
A
C24V
A
C24V
A
C24V
MONIT
OR
OUTPUT 1
VIDEO INPUT 1
TO
CAMERA
RM-P2580
SWITCHER,
etc
Set Pin 1 to "ON" f
or B Mode
.
4. CONNECTIONS
APPLIED SYSTEM (B MODE)
This system accepts the connection of up to 16 cameras.
The video is recor
ded b
y
means of a s
witc
her
, etc.
Setting Pr
ocedure
1.
Connect all the equipment.
(All of the cameras must be synchronized)
2.
Set the system mode selection to B Mode, and set
the rear DIP Switch1 to "ON".
3.
To
set a camera ( REF
. : Instruction Manual of the
camera being used)
· Match
the ID with the VIDEO INPUT
number
.
·
Set to MUL
TIDROP
and DUPLEX
4.
Preset positions ( REF
. : page 27)
5.
Operational setting values can be changed as re-
quired.
· P/T
SPEED: 8 STEPS ( REF
. : page 29)
Read the "Instruction Manual" for each piece of equipment to be
connected before performing the connection.
Contact your JVC sales agent for the switcher
, etc. details.
