E-28
1.
Press and hold the MENU button for about 3 seconds to
display the SETUP
screen.
2.
Select CAMERA
and press the SET
button.
The menu screen for the connected cameras is displayed.
5. MENU SCREEN SETUPS
CAMERA SCREEN
To
set up the connected cameras,
please refer to the instruction man
uals of the individual cameras.
Use the f
ollo
wing pr
ocedure to displa
y the men
u.
1.
Press and hold the MENU button for about 3 seconds to
display the SETUP
screen.
2.
Select CONTROL
UNIT
and press the SET
button.
The CONTROL
UNIT
screen is displayed.
3.
Select an item in the CONTROL
UNIT
screen using the
P
AN/TIL
T
control lever
.
Pressing the SET
button displays a sub-menu at a lower
hierarchical level.
Pressing the MENU button displays a menu at a higher
hierarchical level.
Sub-men
u details
OPTION
:
Used for settings related to the remote control
system.
REF
. : Page 29.
DA
T
A
I/O
:
Used for settings related to the DA
TA
I/O ter-
minals on the rear panel.
REF
. : Page 30.
ALARM
:
Used for settings related to the
ALARM
.
REF
. : Page 32.
AU
TO
SEQ
UENCE
:
Used for settings related to the
AUT
O SEQUENCE operation which
is activated by pressing the
AUT
O
button.
REF
. : Page 32.
CONTR
OL UNIT SCREEN
This screen is used to set the functions of the remote contr
ol unit.
SETUPSETUP
MENUMENU
SETSET
SPEEDSPEED
IRISIRIS
AFAF
FOCUSFOCUS
ZOOMZOOM
OPENOPEN
FARFAR
TELETELE
CLEARCLEAR
/HOME/HOME
7
4
1
8
0
5
2
9
6
3
ENTERENTER
AUTOAUTO
PANPAN
OPTIONOPTION
1
OPTIONOPTION
2
CAMERACAMERA
POSI-POSI-
TIONTION
AUTOAUTO
PATROLPATROL
CLOSECLOSE
NEARNEAR
WIDEWIDE
AUTOAUTO
F-1F-1
F-2F-2
F-3F-3
PAN/TILT
LENS
CAMERA/POSITIONCAMERA/POSITION
CAMERACAMERA
POSITIONPOSITION
REMOTE CONTROL UNIT REMOTE CONTROL UNIT
RM-P2580
ALARMALARM
POPO
WERWER
KEY LOCKKEY LOCK
SET button
MENU button
SETUP
POSITION SETUP..
CAMERA..
CONTROL UNIT..
SETUP
MENU
SET
SPEED
IRISIRIS
AFAF
FOCUSFOCUS
ZOOMZOOM
OPENOPEN
FAR
TELETELE
CLEAR
/HOME
7
4
1
8
0
5
2
9
6
3
ENTERENTER
AUTO
PAN
OPTIONOPTION
1
OPTIONOPTION
2
CAMERA
POSI-
TIONTION
AUTO
PATROL
CLOSECLOSE
NEAR
WIDE
AUTO
F-1
F-2
F-3
PAN/TILT
LENSLENS
CAMERA/POSITIONCAMERA/POSITION
CAMERA
POSITIONPOSITION
REMOTE CONTROL UNIT REMOTE CONTROL UNIT
RM-P2580RM-P2580
ALARMALARM
PO
WER
KEY LOCKKEY LOCK
SET button
MENU button
CONTROL UNIT
OPTION..
DATA I/O..
ALARM.. AUTO SEQUENCE..
SETUP
POSITION SETUP..
CAMERA..
CONTROL UNIT..
2.
3.
2.
(Displayed in
A
mode only)
E-29
OPTION SCREEN
5. MENU SCREEN SETUPS
Item
MAX CAMERA
(Displayed at B
Mode only)
P/T SPEED
SERIAL-2
(Displayed at B
Mode only)
CAMERA
SELECTION
(Displayed at
A
Mode Only)
FA
C
T
O
R
Y
SETTING
Options
1, 2,... 15, 16
2 STEPS,
4 STEPS,
6 STEPS,
8 STEPS
OFF
,
A,
B
AUT
O,
ENABLE,
DISABLE
CANCEL,
EXECUTE
Default
16
8 STEPS
OFF
AUT
O
CANCEL
CAMERA SELECTION
CAMERA 1
AUTO
CAMERA 2
AUTO
CAMERA 3
AUTO
CAMERA 4
AUTO
CAMERA 5
AUTO
CAMERA 6
AUTO
CAMERA 7
AUTO
CAMERA 8
AUTO
FACTORY SETTING
CANCEL
EXECUTE
Function
Sets the maximum number of connected cameras.
Sets the number of cameras to be displayed in the CAMERA
SELECTION screen.
Sets the number of speed steps to be varied according to the
tilting angle during manual operation of the P
AN/TIL
T
control
lever
.
Function not available Make sure that it is set to “OFF”.
Sets to disable or enable the camera selection of each camera.
AU
TO
:
The sync signal of each camera connected is
checked in turn and the camera can be selected if it
is connected correctly
.
ENABLE
:C
amera selection is possible even if the correspond-
ing camera is not connected.
A
blue screen is dis-
played when a camera input is selected without a
camera being connected.
DISABLE
:
Camera selection is disabled.
NO
TE:
Make sure to set to ENABLE when switching the video
signal of the unit with the CAM SW signal from a time lapse
VTR. Even if it is set to
AUT
O, the video signal will not be
switched.
Resets all values to the factory-set defaults.
CANCEL
:
Reset to the factory-set defaults does not occur
but return to the OPTION screen occurs.
EXECUTE
:
When the SET
button is pressed, the “NOW EX-
ECUTING” is displayed and the values are reset
to the factory-set defaults.
At this time “TURN
POWER OFF” is displayed, be sure to then turn
the power of
f and then to ON again in order to
restart.
NO
TE:
The POSITION setting is not returned to the default value.
Slow
Fast
