Juniper SRX240 Series Hardware Manual Download Page 50

Page: 50 / 198

Table 15: Physical Specifications for the SRX240 Services
Gateway

(continued)

Value

Specification

•

SRX240 Services Gateway with AC power supply and no PoE
support models: 74 watts

•

SRX240 Services Gateway with AC power supply and PoE support:
86 watts (excluding PoE load)

•

SRX240 Services Gateway with DC power supply models: 72 watts

Average Power
consumption

No performance degradation at upto 10,000 ft (3048 m)

Altitude

5% to 90%, noncondensing

Relative humidity

Normal operation ensured in temperature range 32°F (0°C) through
104°F (40°C)

Nonoperating storage temperature in shipping container: -40°F
(-40°C) to 158°F (70°C)

Temperature

Designed to meet Telcordia Technologies Zone 4 earthquake
requirements

Seismic

•

SRX240 Services Gateway with AC power supply and no PoE
support models: 427 BTU/hour

•

SRX240 Services Gateway with AC power supply and PoE support
models: 560 BTU/hour (Excluding PoE load)

•

SRX240 Services Gateway with DC power supply models: 409
BTU/hour

NOTE:

These specifications are estimates and subject to change.

Maximum thermal
output

Less than 70 dB(A) as per EN ISO 7779

Noise level

NOTE:

Before removing or installing components of a functioning services

gateway, attach an electrostatic discharge (ESD) strap to an ESD point and
fasten the other end of the strap around your bare wrist. Failure to use an
ESD strap could result in damage to the services gateway.

Documentation

SRX240 Services Gateway Description on page 3

•

SRX240 Services Gateway Hardware Features on page 4

•

SRX240 Services Gateway Front Panel and Back Panel Views on page 13

•

SRX240 Services Gateway Built-In Interfaces on page 16

•

SRX240 Services Gateway LEDs on page 18

•

SRX240 Services Gateway Power Supply on page 25

•

SRX240 Services Gateway Cooling System on page 23

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands