Juniper SRX240 Series Hardware Manual Download

Page: 22 / 198

Documentation

SRX240 Services Gateway Chassis on page 31

•

SRX240 Services Gateway Hardware Features

Table 3 on page 4

lists the hardware features supported on various models of the

SRX240 Services Gateway.

Table 3: SRX240 Services Gateway Hardware Features

SRX240 Services
Gateway with DC
Power Supply

SRX240 Services
Gateway with AC
Power Supply and
PoE Support

SRX240 Services
Gateway with AC
Power Supply and
No PoE Support

Features

•

For SRX240H-DC:
1 GB

•

For SRX240H2-DC:
2 GB

•

For SRX240H-POE:
1 GB

•

For
SRX240H2-POE:
2 GB

•

For
SRX240H-POE-TAA:
1 GB

•

For
SRX240H2-POE-TAA:
2 GB

•

For SRX240B:
512 MB

•

For SRX240B2:
1 GB

•

For SRX240H:
1 GB

•

For SRX240H2:
2 GB

•

For SRX240H-TAA:
1 GB

•

For
SRX240H2-TAA:
2 GB

DDR memory

Yes

PoE support

190 watts

360 watts

150 watts

Power supply rating

–48 VDC

Operating range:
-40.5 V to -72 V

100 to 240 VAC

Input voltage

Gigabit Ethernet ports

Console ports

Universal Serial Bus
(USB) ports

Mini-PIM slots

Status, Alarm, HA,
Power, Mini-PIMs,
Port (TX/RX/Link and
PoE), DC power feed
LEDs.

Status, Alarm, HA,
Power, Mini-PIMs, and
Port (TX/RX/Link and
PoE)

LEDs

NOTE:

The PoE LED is enabled only on the PoE variant of the SRX240 Services Gateway.

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands