Juniper SRX240 Series Hardware Manual Download Page 49

Page: 49 / 198

NOTE:

Install the device only in restricted areas, such as dedicated

equipment rooms and equipment closets, in accordance with Articles
110-16, 110-17, and 110-18 of the National Electrical Code, ANSI/NFPA 70.

Documentation

SRX240 Services Gateway Chassis on page 31

•

SRX240 Services Gateway Site Electrical Wiring Guidelines on page 35

•

SRX240 Services Gateway Rack Requirements on page 33

•

Clearance Requirements for Airflow and Hardware Maintenance on the SRX240 Services
Gateway on page 33

•

Interface Cable and Wire Specifications for the SRX240 Services Gateway on page 41

SRX240 Services Gateway Chassis

Figure 1 on page 3

shows the SRX240 Services Gateway chassis.

Figure 9: SRX240 Services Gateway

g037515

Table 15 on page 31

provides information about the physical specifications for the services

gateway.

Table 15: Physical Specifications for the SRX240 Services Gateway

Value

Specification

1 unit (U)

Chassis height

17.5 in. (44.5 cm)

Chassis width

15 in. (38.1 cm)

Chassis depth

•

SRX240 Services Gateway with AC power supply and no PoE
support models: 11.24 lb. (5.1 kg)

•

SRX240 Services Gateway with AC power supply and PoE support
models: 12.34 lb. (5.6 kg)

•

SRX240 Services Gateway with DC power supply models: 12.56 lb.
(5.7 kg)

Chassis weight

Chapter 6: Planning and Preparing the Site

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands