Juniper SRX240 Series Hardware Manual Download

Page: 34 / 198

Table 8: SRX240 Services Gateway Back Panel DC power supply models

Component

Number

Air filter slot

Cable tie holder

DC power feed LEDs

DC power feed

Grounding point

Documentation

SRX240 Services Gateway Hardware Features on page 4

•

SRX240 Services Gateway Chassis on page 31

•

SRX240 Services Gateway Built-In Interfaces on page 16

•

SRX240 Services Gateway LEDs on page 18

•

SRX240 Services Gateway Boot Devices and Dual-Root Partitioning Scheme on page 10

•

SRX240 Services Gateway Power Supply on page 25

•

SRX240 Services Gateway Cooling System on page 23

SRX240 Services Gateway Built-In Interfaces

Table 9 on page 16

describes the built-in interface ports on the SRX240 Services Gateway.

Table 9: SRX240 Services Gateway Built-In Interfaces

Usage

Description

Interface Type

Function as front-end network ports and
provide LAN and WAN connectivity to hubs,
switches, local servers, and workstations.

•

16 ports, labeled 0/0
through 0/15, built into
the chassis front panel

•

Provide link speeds of
10/100/1000 Mbps

•

Operate in full-duplex
and half-duplex
modes

NOTE:

On the PoE

models of the SRX240
Services Gateway, all 16
Gigabit Ethernet ports
support PoE.

Gigabit Ethernet

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands