Juniper SRX240 Series Hardware Manual Download Page 126

Page: 126 / 198

Table 41: Component LEDs on the SRX240 Services Gateway

(continued)

Possible Causes and
Corrective Actions

Meaning

State

LED

A major alarm indicates a
critical situation on the
gateway that requires
immediate action. See

“Monitoring the SRX240
Services Gateway Using
Chassis Alarm Conditions”
on page 113

The services gateway
detects a major alarm.

Red

Alarm LED

A minor alarm requires
monitoring or maintenance.
If left unchecked, it might
cause an interruption in
service or degradation in
performance. See

“Monitoring the SRX240
Services Gateway Using
Chassis Alarm Conditions”
on page 113

Indicates a minor alarm.

NOTE:

The Alarm LED glows

Yellow while initializing.

Yellow

Normal condition. No action
is required.

The services gateway is
starting up.

NOTE:

When the system is

up and running, if the Alarm
LED is off, it indicates that no
alarms are active on the
services gateway.

Off

Normal condition. No action
is required.

The services gateway is
receiving power supply and
is functioning normally.

Green

Power LED

Normal condition. No action
is required.

The Power button has been
pressed and quickly released.

Amber

Normal condition if the
services gateway is
switched off. No action is
required.

If you have not powered off
the services gateway, verify
that the AC power cord
from the power source to
the device is not damaged,
the socket is in working
condition, and the device
has an AC input voltage
between 110 and 240 VAC.
See

“Monitoring the

SRX240 Services Gateway
Power System” on page 115

The services gateway is not
receiving power.

Off

108

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands