Juniper SRX240 Series Hardware Manual Download Page 59

Page: 59 / 198

CHAPTER 8

Cable Specifications and Pinouts

•

Interface Cable and Wire Specifications for the SRX240 Services Gateway on page 41

•

RJ-45 Connector Pinouts for the SRX240 Services Gateway Ethernet Port on page 41

•

RJ-45 Connector Pinouts for the SRX240 Services Gateway Console Port on page 43

Interface Cable and Wire Specifications for the SRX240 Services Gateway

Table 23 on page 41

lists the specifications for the cables that connect to ports.

Table 23: Cable and Wire Specifications for Ports

Device
Receptacle

Maximum
Length

Cable/Wire Required

Cable Specification

Port

RJ-45

6 ft (1.83 m)

One 6-ft (1.83-m) length
with DB-9/RJ-45
connectors

RS-232 (EIA-232) serial
cable

Console
port

RJ-45

328 ft
(100 m)

One 15-ft (4.57-m)
length with RJ-45/RJ-45
connectors

CAT-5e (Category 5)
cable or equivalent
suitable for 100BASE-T
operation

Ethernet
port

Documentation

RJ-45 Connector Pinouts for the SRX240 Services Gateway Ethernet Port on page 41

•

RJ-45 Connector Pinouts for the SRX240 Services Gateway Console Port on page 43

RJ-45 Connector Pinouts for the SRX240 Services Gateway Ethernet Port

Figure 10 on page 41

shows the RJ-45 cable connector pinouts for Ethernet ports.

Figure 10: Ethernet Cable Connector (RJ-45)

Table 24 on page 42

describes the RJ-45 connector pinouts for the Ethernet port for

10/100 Mbps.

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands