JUKI DP-2100 Instruction Manual Download Page 176

Page: 176 / 187

−

170

−

24-2 Changing the amount of alternate vertical movement of walking
foot and presser foot

Cam rod position

Top feed arm lowest position

Amount of alternate vertical movement of walking foot

0.2 to 0.3 mm

Clearance at lower dead point of walking foot

0.1mm

Amount of alternate vertical movement of presser foot

Approximately 2.7 mm

Clearance at lower dead point of presser foot

0.1mm

When changing the amount of alternate vertical movement, change max. sewing speed.

When it is not changed, components breakage or damage occurs and the life of the machine is

excessively shortened.

Amount of vertical movement of walking foot (mm)

Less than 0.3 Up to 1.5

Up to 2.5

Up to 3.5

Amount of vertical movement of presser foot (mm)

2.7

1.5

2.5

3.5

Max. sewing speed (rpm)

3500

2600

2000

1600

(1) State of walking foot and presser foot at the time of delivery

(2) Relation between amount of alternate vertical movement and max. sewing speed

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the
sewing machine.

Summary of Contents for DP-2100




























































































































































































Search results

Summary of Contents for DP-2100

Reviews:

Related manuals for DP-2100

Brands by name

Popular brands

JUKI DP-2100, Instruction Manual

Search results

Summary of Contents for DP-2100

Reviews:

Related manuals for DP-2100

Brands by name

Popular brands