JUKI DP-2100 Instruction Manual Download Page 174

Page: 174 / 187

−

168

−

Feed pitch error will be caused unless

the tension is proper.

(1) Replacing the top feed belt

24-1 Replacing procedure of feed belt

Caution : The standard of the time of replacement is one year although it depends on the

frequency of use.Replace the belt with a new one when it is observed that feed force is
excessively deteriorated or the like.

Caution : Perform periodical cleaning approximately once a week since dust is collected inside the

top feed cover and the belt rolls the dust resulting in feed trouble or short life of the belt.

■

Belt tension adjusting procedure

(1) Main feed belt :

Move tension adjustment plate L

to the left or

right to adjust the belt.

• The tension is increased in the right-hand

direction (direction A) and decreased in the left

direction.

(2) Auxiliary feed belt :

Move tension adjustment plate S

to the left or

right to adjust the belt.

• When it is opened on both sides (direction B),

the tension is increased, and when it is closed, the

tension is decreased.

(3) Adjusting the belt tension value :

1) Main feed belt :

The belt has to be bent by 3 mm when it is

pressed with a load of 1.3N (130gf).

2) Auxiliary feed belt :

The belt has to be bent by 3 mm when it is

pressed with a load of 0.4N (40gf).

24. MAINTENANCE

Remove ten cover setscrews

and remove

coverR

and cover F

Loosen intermediate presser foot screw

and

remove intermediate presser foot

Loosen walking foot setscrew

and remove

walking foot

and auxiliary walking foot

Remove main feed belt

and auxiliary feed belt

, and replace them with new ones.

Put walking foot rod

between

and

, and fix

with screw

After adjusting the belt tension, attach cover R

and cover F

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the
sewing machine.

Press the center.

Summary of Contents for DP-2100




























































































































































































Search results

Summary of Contents for DP-2100

Reviews:

Related manuals for DP-2100

Brands by name

Popular brands

JUKI DP-2100, Instruction Manual

Search results

Summary of Contents for DP-2100

Reviews:

Related manuals for DP-2100

Brands by name

Popular brands